733964
24
Zoom out
Zoom in
Previous page
1/168
Next page
CAUTION: Spark plugs that are not
tightened correctly can cause damage to
the engine.
CAUTION: Do not try to start the engine
if the spark plug or ignition cable is
removed.
To replace the fuses
The fuses are put in 2 groups. The fuses for the mower
control module and the engine are in a holder in front of
the battery. The fuses for auxiliary electrical outputs are
in a holder in front of the hydraulic oil cooler. A blown
fuse is identified by a burned connector.
1. Open the engine cover.
2. Pull the fuse from the holder.
3. Replace the blown fuse.
4. Close the engine cover.
If the fuse blows again a short period after you replace
it, there is a short circuit. Repair the short circuit before
you operate the product again.
To charge the battery
Charge the battery if it is too weak to start the
engine.
Use a standard battery charger.
CAUTION: Do not use a boost charger
or start booster. That will cause damage
to the electrical system of the product.
Always disconnect the charger before starting the
engine.
To do an emergency start of the engine
If the battery is too weak to start the engine, you can use
jumper cables to do an emergency start. This product
has a 12 V system with negative ground. The product
that is used for the emergency start must also have a 12
V system with negative ground.
To connect the jumper cables
WARNING: Risk of explosion because of
explosive gas that comes from the battery.
Do not connect the negative terminal of the
fully charged battery to or near the negative
terminal of the weak battery.
CAUTION: Do not use the battery of your
product to start other vehicles.
1. Remove the engine cover.
2. Connect one end of the red cable to the POSITIVE
battery terminal (+) on the weak battery (A).
B
A
C
D
3. Connect the other end of the red cable to the
POSITIVE battery terminal (+) on the fully charged
battery (B).
WARNING: Do not short circuit the ends
of the red cable against the chassis.
4. Connect one end of the black cable to the
NEGATIVE battery terminal (-) on the fully charged
battery (C).
5. Connect the other end of the black cable to a
CHASSIS GROUND (D), away from the fuel tank
and the battery.
6. Replace the covers.
To remove the jumper cables
Note: Remove the jumper cables in the opposite
sequence to how you connect them.
1. Remove the BLACK cable from the chassis.
2. Remove the BLACK cable from the fully charged
battery.
3. Remove the RED cable from the 2 batteries.
24 880 - 002 - 28.02.2019
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna R 420TsX AWD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna R 420TsX AWD in the language / languages: English, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 11,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna R 420TsX AWD

Husqvarna R 420TsX AWD User Manual - German, Dutch, French - 172 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info