610265
15
Zoom out
Zoom in
Previous page
1/62
Next page
Accessory
box
Glide
plates
The
glide
plates
fit
presser
foot
A
and
E.
These
plates
can
be
used
when
sewing
on
foam
plastic,
plastic-coated
fabric
and
leather
imitations.
They
will
minimize
the
risk
of
these
materials
sticking
to
the
presser
foot.
Peel
off
the
protective
paper
and
press
the
self-adhe
sive
side
of
the
glide
plate
against
the
underside
of
the
presser
foot.
Changing
the
presser
foot
If
you
wish
to
change
the
presser
foot,
check
that
the
needle
is
at
its
upper
position.
Remove
the
presser
foot
by
drawing
it
toward
you
while
pressing
slightly
down
ward.
Insert
the
new
presser
foot
in
such
a
way
that
the
round,
horizontal
pin
fits
in
between
the
spring
and
the
presser
foot
ankle.
Press
slightly
downward
and
back
ward
and
the
foot
will
snap
into
place.
Edge
guide
The
stitch
plate
has
markings
for
1.0,
1.5,
2.0,
2.5,
3.0
and
3.5
cm,
to
simplify
sewing
seam
allowances.
If
you
require
an
even
wider
seam
allowance,
use
the
edge
guide.
First
loosen
the
screw
at
the
rear
of
the
presser
bar
as
far
as
it
will
go.
Insert
the
guide
into
the
groove
under
the
screw
and
adjust
it
to
the
required
seam
allowance.
Tighten
the
screw,
using
the
screwdriver.
15
15


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-prisma-940

Reset search

  • Please clear and explain about hosquarna prisma 940adaptor including voltage and current thanks a lot
    Mohamadlajevardi@gmail.com Submitted on 15-12-2022 at 17:49

    Reply Report abuse
  • Please clear and explain about hosquarna prisma 940adaptor including voltage and current thanks a lot
    Mohamad lajevardi@gmail.com Submitted on 15-12-2022 at 17:47

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Prisma 940 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Prisma 940 in the language / languages: English as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info