518132
16
Zoom out
Zoom in
Previous page
1/38
Next page
u
roll,
I’Ia!,,un,
O
Edging
FootJ
This
toot
is
used
for
overcasting,
seam
I
and
overcasting,
i.e.
stitches
which
have
a
stitch
width
of
5.0
and
5
mm.
Stitches
I
t
Lf
form
over
the
pin
which prevents
puck-
ering
at
the
edge
of
the
fabric.
LJ
Sensor Buttonhole
Foot
When
connected
to
the
machine
it
gives
a
butk)nhole
length
fitting
the
button
size
that
has
been
entered
into
the
machine.
The
middle
mark
gives
a
9/16
(IS
mm)
buttoning
edge.
Read
more
about
di
erent
optional
pres.cer/et
in
the
Accessory
[er
Guide.
Changing
the
Presser
Foot
I
Make
sure
that
the
needle
is
in
the
highest
position.
Pull
the
presser
foot
towards
you.
2
Line
up
the
cross
pin
Ofl
the
foot
with
the
gap
in
the
presser
foot
ankle.
Press
back
until the
foot
snaps
into
place.
Presser
Foot
Pressure
(a)
The
presser
foot
pressure
is
adjusted
with
the
dial
found
under
the
lid
on
your
Platinum
30.
Normal
setting
is
around
four.
The
higher
the
number
the more
pressure
the
foot
puts
on
the
fabric.
Knit
and
soft
fabrics
should
be
sewn
at
lower
pressure.
Presser
Foot
Lever
(b)
The
presser
foot
is
raised
and
lowered
with
the
presser
foot
lever.
The
presser
toot
must
be
lowered
when
sewing.
By
raising
the
presser
foot
lever
and
then
press
it
upwards,
the
lift
height
of
the
presser
foot
can
be
raised
to extra
height
in
order
to
slide
thick
projects
under
the
foot.
2
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Platinum 730 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Platinum 730 in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info