595367
36
Zoom out
Zoom in
Previous page
1/48
Next page
36 – English
MAINTENANCE AND SERVICE
The cutting unit bevel gear
Check the oil level
Check the oil level when the cutting deck is in its lowest
position.
Insert a clean metal rod (approx. Ø3 mm) through the filler
plug. Lower the rod until it reaches the bottom of the gear
housing (approx. 90 mm).
Pull up the metal rod and read off the oil level. The oil level
must be between 18-22 mm from the end of the rod.
Fill with transmission fluid SAE 80W/90 as necessary.
Changing the oil
Empty the bevel gear through the filler plug using a pump
fitted with a plastic tube that extends to the bottom of the
housing.
Alternative: Remove the cutting unit and plastic covers.
Place the cutting unit on its edge and empty the bevel gear
through the plug.
Fill the bevel gear with 80 ml of transmission fluid SAE
80W/90
Checking the engine’s oil level.
Check the oil level in the engine when the Rider stands
horizontal with the engine switched off. Do not check the oil
with the engine running.
Open the engine cover.
Loosen the dipstick, pull it up and wipe it off.
Now insert the dipstick again, without tightening it.
Pull the dipstick out again and read the oil level.
The oil level should be between the markings on the dipstick.
If the level is approaching the ADD mark, top up the oil to
the FULL mark on the dipstick.
The oil filler is on the valve cap.
Tighten the dipstick correctly before starting the engine.
Start and run the engine at idling speed for approx. 30
seconds.
Turn off the motor. Wait 30 seconds and check the oil
level.
If necessary fill so that the oil comes up to the FULL mark
on the dipstick.
The following oil classes are recommended:
API Service Class: CH4 or ACEA E5 or higher.
Choose an oil with viscosity according to the temperature
ranges in the figure:
Do not mix different types of oil.
Replacing the engine oil
The engine oil should be changed the first time after 25 hours
running time. It should then be changed after every 100 hours
of running time.
1 Open the engine cover.
2 Place a container underneath the engine oil drain plug.
3 Remove the dipstick. Remove the drain plug from the
engine.
4 Let the oil run out into the container.
5 Fit the drain plug and tighten it.
6 Change oil filter if necessary.
CAUTION! Too high an oil level increases the risk of oil
leakage.
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
-30 -20 -10 0 10 20 30 40 50 C
-22 -4 -14 32 50 68 86 104 122 F
0W
5W 20
10W 30
20
30
40
15W 40
20W 50
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna P 525D - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna P 525D - 2015 in the language / languages: English as an attachment in your email.

The manual is 12,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna P 525D - 2015

Husqvarna P 525D - 2015 User Manual - German - 48 pages

Husqvarna P 525D - 2015 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info