477558

Husqvarna LT126 Manual

59
Zoom out
Zoom in
Previous page
1/76
Next page
59
6
To Level Mower
Make sure tires are properly inflated to the PSI shown on
tires. If tires are over or under inflated, it may affect the ap-
pearance of your lawn and lead you to think the mower is
not adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT
1. With all tires properly inflated and if your lawn appears un-
evenly cut, determine which side of mower is cutting lower.
2. With a 3/4" or adjustable wrench, turn lift link adjustment
nut (A) to the left to lower the mower, or, to the right to
raise the mower (Fig. 1).
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
3. Test your adjustment by mowing some uncut grass and
visually checking the appearance. Readjust, if necessary,
until you are satisfied with the results.
PRECISION SIDE-TO-SIDE ADJUSTMENT
1. With all tires properly inflated, park tractor on level ground
or driveway.
CAUTION: Blade is sharp. Protect your hands with gloves
and/or wrap blade with heavy cloth.
2. Raise mower to its highest position.
3. At both sides of mower, position blade at side and measure
the distance (A) from bottom edge of blade to the ground.
The distance should be the same on both sides (Fig. 2).
4. If adjustment is necessary, see step 2 in Visual Adjust-
ment instructions above.
5. Recheck measurements, adjust if necessary until both
sides are equal.
FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting re sults, the mower blades should
be adjusted so the front tip is 1/8" to 3/8" lower than the rear
tip when the mower is in its highest position.
CAUTION: Blade is sharp. Protect your hands with gloves
and/or wrap blade with heavy cloth.
• Raise mower to highest position.
• Position blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear tip
of the blade (Fig. 3).
• If front tip of blade is not 1/8" to 3/8" lower than the rear
tip, go to the front of tractor.
• With an 11/16" or adjustable wrench, loosen jam nut A
several turns to clear adjustment nut B.
• With a 3/4" or adjustable wrench, turn front link adjustment
nut (B) clockwise (ltighten) to raise the front of mower, or,
counterclockwise (loosen) to lower the front mower (Fig. 4).
NOTE: Each full turn of the adjustment nut will change mower
height about 1/8".
• Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 3/8" lower than the rear tip.
• Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.
0
2
9
4
8
A
0
2
4
7
3
0
247
3
Fig. 1
02966
A
A
Fig. 2
02548
B
B
Fig. 3
B
02950
A
0
2
4
7
3
024
7
3
B
Fig. 4
… 59 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LT126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LT126 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info