477558

Husqvarna LT126 Manual

34
Zoom out
Zoom in
Previous page
1/76
Next page
34
Turn the ignition key to “START position”.
NOTE
Do not run the start motor more than 5 sec onds at once. If
the engine will not start, wait about 10 sec onds before the
next try.
Zündschlüssel auf “START” drehen.
HINWEIS
Den Anlasser nicht jeweils länger als ca. 5 Sekunden betäti-
gen. Wenn der Motor nicht anspringt, vor dem nächsten
Anlaßversuch ca. 10 Sekunden warten.
Tourner la clef de contact en position de démarrage
“START”.
REMARQUE
Ne pas faire tourner le démarreur pendant plus de 5 secondes
à la fois. Si le moteur ne démarre pas, attendre une dizaine
de secondes avant de refaire un essai de démarrage.
Ponga la llave de encendido en la posición de arranque
”START”.
NOTA
No haga funcionar el motor de arranque más de unos 5
segundos a la vez. Si el motor no arranca, espere unos 10
segundos antes de hacer otra tentativa.
Girare la chiave su “START”.
NOTA
Non inserire il motorino di avviamento per più di 5 secondi
per volta. Se il motore non parte attendere una decina di
secondi prima di riprovare.
Draai de startsleutel naar “START”-positie.
N.B.
Laat de startmotor niet langer dan ca 5 sek. per keer draaien.
Als de motor niet start, wacht dan ca 10 sek voordat u vol-
gende poging doet.
0
2
9
2
7
Let the ignition key return to the ”ON” position when the en-
gine has started Push the gas control to the re quired speed.
For cutting: full gas.
Nach Anspringen des Motors den Zündschlüssel in die
Stellung “ON” zurückgehen lassen. Den Gashebel auf die
gewünschte Motordrehzahl stellen. Bei Mähen: Vollgas.
Laisser revenir la clef de contact à la position “ON” lorsque le
moteur a démarré. Amener la manette de gaz à la po si tion de
régime moteur désiré. Pour la coupe, positionner la manette
dans l'encoche correspondant au régime moteur optimal pour
la tonte (accélération maximale du moteur).
Dejar que la llave de encendido vuelva a la posición “ON”
cuando ha arrancado el motor. Ponga el acelerador en la
posición deseada. Al cortar, a plenos gases.
Dopo l’avviamento, riportare la chiave su “ON”. Regolare il gas
sul regime desiderato. Per il taglio: massimo regime “F”.
Draai de startsleutel terug in “ON”-posotie. Schuif de gash-
endel naar het gewenste toerental. Bij maaien: vol gas.
Warm motor: Push the gas control half-way to full gas
position " ".
Bei warmem Motor: Gashebel in die Vollgasstellung "
"
schieben.
Si le moteur est chaud: pousser la commande des gaz à mi-
distance de sa position d'accélération maximale. " ".
Moter caliente: Empuje el acelerador hasta la mitad de su
recorrido hacia la posición de plenos gases " ".
Motore caldo: Portare il comando del gas sul massimo " ".
Bij een warme motor: Schuif de gashendel halverwege naar
de volgaspositie " ".
5
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LT126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LT126 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info