518115
28
Zoom out
Zoom in
Previous page
1/32
Next page
26
Trouble Shooting
Trouble Shooting
Always Start by Checking the Needle
• Always start with a new needle as soon
as you discover that a stitch is not what
you expected. Test sew on a scrap of the
fabric you are sewing. Check that you
have chosen the correct needle and see
that it is correctly inserted. See page 11.
Unattractive Stitches
• The thread tension is not correct. See page
10.
• Make sure that the thread is not catching.
Certain thread spools are unsuitable for
spooling from the horizontal spool pin.
Try instead with the vertical spool pin.
• The machine may be incorrectly threaded.
Be sure to place spool holders correctly.
The correct threading is shown on page 7.
• Wrong bobbin thread. It should be of the
same thickness as the upper thread.
The Needle Breaks
• You may have helped the machine to
feed by pulling the fabric. The needle
can strike against stitch plate and break.
Change the needle. See page 11.
The Upper Thread Breaks
• Check the thread spool to see that it has
not caught in any way.
• The needle eye may have sharp edges
which cut the thread. If so, change the
needle. See page 11.
• The upper thread is incorrectly threaded.
See page 7.
• The upper thread may have too much
tension. Refer to page 10.
The Thread is Knotted
• The hole in the stitch plate may be chip-
ped and have sharp edges. We recom-
mend that you replace it.
The Bobbin Thread Breaks
• The bobbin thread may be incorrectly
threaded. See page 9.
• The stitch plate hole is damaged. See ”The
thread is knotted”.
Irregular Bobbin Winding
• This may be due to poor quality thread.
When sewing with cotton thread, increase
the thread tension.
• The machine is not correctly threaded for
bobbin winding. See page 7-9.
The Fabric Puckers
• The upper thread tension is too tight. See
page 10 for correct thread tension.
The Machine Does Not Feed the Fabric
• The stitch length is too short. Increase
stitch length.
• The feed teeth may be lowered. Raise
them by turning the stitch length dial to
the left.
• The feed teeth are full of dust and dirt.
Clean with the brush. See page 25.
The Seam is Too Loose – Fabric Layers
Not Held Together
• The thread tension is far too loose. Page
10 shows how to adjust the thread ten-
sion.
Machine Runs Sluggishly
• Dirt or lint has built up under the stitch
plate. Loosen the plate and brush clean
between the feed teeth and in the bottom
area. See page 25.
• Dirt or lint has packed in the hook.
Remove the bobbin and clean with the
brush. See page 25.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Lena at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Lena in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info