733935

Husqvarna LC 451S Manual

11
Zoom out
Zoom in
Previous page
1/352
Next page
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved Husqvarna service agent.
• Let an approved Husqvarna service agent do
servicing on the product regularly.
• Replace damaged, worn or broken parts.
Assembly
Introduction
WARNING: Before you assemble the
product, you must read and understand the
safety chapter.
WARNING: Remove the spark plug cable
from the spark plug before you assemble the
product.
To assemble the handle
1. Loosen the lower knobs on the left and the right side
of the product. Make sure that the plastic washer is
in the recess in the handle bracket. (Fig. 29)
2. Install the handle folded forward as shown in the
illustration. (Fig. 30)
a) Make sure that the plastic washer is between the
handle and the handle bracket.
b) Attach the handle to the handle bracket.
3. Lift the handle up. (Fig. 31)
4. Tighten the knobs fully. To adjust the handle height,
refer to
To adjust the handle height on page 11
.
5. Put the wires in the cable brackets. Make sure that
the wires are not twisted. Attach the cable brackets
to the handle. (Fig. 32)
6. Use a cable tie to attach the cables to the handle
bracket. (Fig. 33)
To adjust the handle height
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 34)
3. Set the handle height in 1 of the 2 available
positions.
4. Move the knobs up in the direction of the handlebar
until they stop and you hear a click. (Fig. 35)
5. Tighten the knobs fully.
To set the product in transport position
1. Remove the grass catcher.
2. Loosen the lower knobs.
3. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 34)
4. Fold the handle forward. (Fig. 36)
To set the product in operation position
1. Lift the handlebar up. (Fig. 31)
2. Move the knobs up in the direction of the handlebar
until they stop and you hear a click. (Fig. 35)
3. Tighten the knobs fully.
To assemble the grass catcher
1. Attach the grass catcher frame to the grass bag with
the rigid part of the bag on the bottom. Keep the
handle of the frame on top of the grass bag. (Fig. 37)
2. Attach the bottom of the grass catcher frame to the
bottom of the grass bag. (Fig. 38)
a) Push the grass catcher frame into the groove.
Start at the right side as shown in the illustration
and move gradually to the left.
3. If the grass catcher frame is not easy to attach, hit
the grass catcher frame carefully with a rubber
mallet. Hit the grass catcher frame between the
reinforcements. (Fig. 39)
4. Attach the grass bag to the grass catcher frame with
the clips. (Fig. 40)
5. Lift the rear cover.
6. Attach the grass catcher to the top edge of the
chassis.
7. Put the lower part of the grass catcher into the grass
discharge channel. (Fig. 41)
To assemble the mulch plug
(accessory)
1. Lift up the rear cover and remove the grass catcher.
2. Put the mulch plug into the discharge channel. (Fig.
42)
3. Replace the blade with the mulch blade that is
supplied with the mulch kit. Refer to
To replace the
blade on page 14
.
To cut grass without a grass catcher or
mulch plug attached
• Lift up the rear cover and remove the grass catcher.
• If a mulch plug and a mulch blade are attached,
remove them.
• Close the rear cover before you operate the product.
When you operate the product, the cut grass discharges
below the rear cover.
929 - 002 -
11
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 451S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 451S in the language / languages: All languages as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info