579216
14
Zoom out
Zoom in
Previous page
1/124
Next page
MAINTENANCE
14 – English
Replacing and adjusting the
centre belt
The centre belt runs between the engine shaft and the
gearbox.
Adjusting the centre belt
Unscrew the adjuster screws a few turns.
Adjust the belt by moving the gear forwards or
bac
kwards.
The belt should be stretched so that it can move 6-
10mm in the centre
. That corresponds to a pull of
approx. 3 kg. Use a fishing scale to check.
Tighten the adjustment screws properly. (3 Nm)
Check the drive operation, as adjustment of the gear
aff
ects the belt tension in the gearbox.
Replacing the centre belt
Remove the cutter.
Loosen the adjustment screws.
Replace the belt with a new one and tighten the
adjustment scre
ws a little.
Adjust the centre belt. See instructions under the
heading "Adjusting the centre belt".
Assemble the blade.
Air filter
Remove the air filter cover and take out the filter.
Clean the filter by knocking the filter against a flat
surf
ace. Never use solvent with petroleum, for
example, kerosene, or compressed air to clean the
filter.
An air filter that has been in use for a long time cannot
be cleaned completely. The filter must therefore be
replaced with a new one at regular intervals.
A
damaged air filter must always be replaced.
When reassembling, make sure that the filter
completely seals against the filter holder.
Oil change
Empty the fuel tank.
Unscrew the oil filler cap.
Place a suitable vessel to collect the oil in.
Drain the oil by tipping the engine so that the oil runs
out through the filler pipe
. Ask where you can dispose
of surplus engine oil at your local petrol station.
Fill with new engine oil of a good quality. See
instr
uctions in the section "Technical data".
Oil filter
Unscrew the oil filler cap.
Place a suitable vessel to collect the oil in.
Drain the oil by tipping the engine so that the oil runs
out through the filler pipe
. Ask where you can dispose
of surplus engine oil at your local petrol station.
Unscrew the oil filter. Ask at your local petrol station
where y
ou can dispose of the used oil filter.
Lightly lubricate the rubber seal on the new oil filter
using new oil.
Screw the oil filter back. When the gasket touches the
fixing, tighten 1/2 to 3/4 turn.
Fill with new engine oil of a good quality. See
instructions in the section "Technical data".
Start the engine. Check for leaks while the engine is
heating up.
Stop the engine. Check oil level and top up if
necessary.
Fuel system
Check that the fuel cap and its seal are not damaged.
Check the fuel hose. Replace if necessary.
Recycling
This machine has the prerequisites to last for many years.
This minimizes the machine's environmental impact.
Perform service and maintenance according to the
instructions in this manual. This way the engine will last
longer and the hazardous emissions are minimized.
When the service life of this product has been served and
it is no longer used it should be retur
ned to the dealer or
to an applicable station for recycling. The machine is
dismantled and the parts are divided up in different
materials for recycling. Most parts of this machine are
recyclable.
!
WARNING! The oil filter gets very hot
during and after use. Always wear heavy-
duty work gloves when dismantling the
oil filter.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 448Se at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 448Se in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 20,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info