733924
20
Zoom out
Zoom in
Previous page
1/576
Next page
WARNING: Use heavy duty gloves. The
blade is very sharp and cuts can easily
occur.
10. Start the product to do a test of the blade. If the
blade is not correctly attached, there is vibration in
the product or the cutting result is unsatisfactory.
Troubleshooting
Battery
LED on the battery Possible faults Possible procedure
The green LED is flash-
ing
The battery voltage is low Charge the battery. See
To charge the battery on
page 17
.
The error LED flashes The battery is weak Charge the battery. See
Battery on page 20
.
The temperature in the work environ-
ment is too high or too low
Use the battery in temperatures between -10°C
and 40°C.
Overvoltage Check that the mains voltage is the same as on
the rating plate on the product.
Remove the battery from the battery charger. Wait
5 seconds and try again to charge the battery. If
the problem continues, speak to an authorised
service agent.
The error LED is on Cell difference too much (1V) Speak to an approved service agent.
Battery charger
LED on the battery
charger
Possible faults Possible procedure
The error LED flash-
es
The temperature in the work en-
vironment is too high or too low
Use the battery charger in temperatures between 5°C
and 40°C.
The error LED is on Speak to an approved service agent
Control panel
Keypad Error code (Num-
ber of flashes)
Possible faults Possible action
Error LED flashes 3 The motor is overloaded Increase the cutting height. Refer to
To
set the cutting height on page 16
.
5 The motor speed drops too
much, and the motor stops
10 The motor control is too hot Stop the motor and wait until it has be-
come cool
2 The blade is blocked To prevent accidental start turn the safe-
ty key to 0, remove the battery and wait
a minimum 5 seconds. Make sure that
the blade can rotate freely. If the prob-
lem continues, speak to an authorised
service agent
9 Battery error or no signal from
battery
Put the battery in the product correctly
and examine the battery connector. If the
error LED on the battery flashes. Refer
to
Battery on page 17
.
20 890 - 002 - 21.12.2018
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 353iVX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 353iVX in the language / languages: All languages as an attachment in your email.

The manual is 6,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info