733921
14
Zoom out
Zoom in
Previous page
1/400
Next page
LED display on the battery Status
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED 3 flashes 50%-75%
LED 1, LED 2, LED 3 are lit, LED 4
flashes
75%-100%
LED 1, LED 2, LED 3, LED 4 are lit Fully charged
Lamp indicator on the bat-
tery charger
Status
Constant red light The battery charges
Flashing red light The battery is too warm
and will start to charge
when the temperature is
correct
Constant green light The battery is fully charg-
ed
Flashing red and green
light
The battery is damaged
and must be replaced
Air filter
An air filter that is used for a long time cannot be fully
cleaned. Replace the air filter at regular intervals.
All models except LC 247, LC 247S have a paper filter.
LC 247, LC 247S have a foam plastic filter.
Note:
Always replace a damaged air filter.
To clean the paper filter
1. Remove the air filter cover and remove the paper
filter.
2. Hit the filter against a flat surface to make the
particles fall off.
CAUTION:
Do not use solvent or
compressed air to clean the paper filter.
3. Put the air filter back. Make sure that the air filter
fully seals against the air filter holder.
4. Put the air filter cover back.
To clean the foam plastic filter
1. Remove the air filter cover and remove the foam
plastic filter.
2. Clean the foam plastic filter with soap and water.
3. Flush the foam plastic filter in clean water.
4. Squeeze the water from the foam plastic filter and let
it dry.
CAUTION: Do not use compressed air. It
can cause damage to the foam plastic
filter.
5. Lubricate the foam plastic filter with engine oil.
6. Press a clean cloth against the foam plastic filter to
remove unwanted oil.
7. Put the air filter back. Make sure that the air filter
fully seals against the air filter holder.
8. Put the air filter cover back.
To examine the spark plug
CAUTION: Always use the recommended
spark plug type. Incorrect spark plug type
can cause damage to the product.
Examine the spark plug if the engine is low on
power, is not easy to start or does not operate
correctly at idle speed.
To decrease the risk of unwanted material on the
spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly
adjusted.
b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.
If the spark plug is dirty, clean it and make sure that
the electrode gap is correct, refer to
Technical data
on page 15
. (Fig. 43)
Replace the spark plug if it is necessary.
To examine the fuel system
Examine the fuel tank cap and the seal for the fuel
tank cap to make sure that there are no damages.
Examine the fuel hose to make sure that there are
no leaks. If the fuel hose is damaged, let a service
agent replace it.
To adjust the clutch wire
If the drive starts to feel slow, it is necessary to adjust
the clutch wire.
1. To increase the drive speed, turn the adjuster screw
counterclockwise.
Note:
If the drive is engaged when you do not pull
the drive bail, it is necessary to extend the wire.
2. To extend the wire and decrease the drive speed,
turn the adjustment screw clockwise. (Fig. 44)
If the drive feels slow also after the adjustment, let an
approved service agent replace the drive belt.
14
808 - 004 -
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 347VI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 347VI in the language / languages: All languages as an attachment in your email.

The manual is 4,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info