Manual Husqvarna LC 347VI (page 11 of 400) (All languages)

733921

Zoom out

Zoom in

1/400

3. Fill the fuel tank. See

To fill fuel on page 11

4. Fill the oil tank and do a check of the oil level. See

To do a check of the oil level on page 13

To fill fuel

If available, use low-emission/alkylate gasoline. If low-

emission/alkylate gasoline is not available, use good

quality unleaded gasoline or leaded gasoline with octane

number not less than 90.

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove it

with a cloth and let remaining fuel dry off.

3. Clean the area around the fuel tank cap.

4. Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

5. Move the product a minimum of 3 m (10 ft) from the

position where you filled the tank before a start.

To set the cutting height

The cutting height can be adjusted in 6 levels.

1. Move the cutting height lever rearward to decrease

the cutting height.

2. Move the cutting height lever forward to increase the

cutting height. (Fig. 33)

CAUTION:

Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

To start the product

• Make sure that the ignition cable is connected to the

spark plug.

Manual start (not on LC 347VI, LC 353VI)

1. For LC 247, LC 247S: The very first time you start

the product, press the primer bulb 5 times. The next

time you start the product when the engine is cold,

press the primer bulb 3 times.

2. Stay behind the product.

3. Hold the engine brake handle against the handlebar.

(Fig. 34)

4. Hold the starter rope handle with your right hand.

5. Slowly pull out the starter rope until you feel some

resistance.

6. Pull with force to start the engine.

WARNING: Do not twist the starter rope

around your hand.

Electrical start (LC 347VI, LC 353VI)

1. Make sure that the battery is activated and charged.

See

To start the battery on page 13

2. Attach the battery to the engine. (Fig. 35)

3. Push the start inhibitor out to the right (A).

4. Pull the start bar (B) against the handlebar to start

the starter motor. The starter motor stops when the

engine starts. (Fig. 24)

To use the drive on the wheels

• For LC 247S, LC 247SP: Pull the drive bail in the

direction of the handlebar. (Fig. 36)

• For LC 347V, LC 347VI, LC 353V, LC 353VI: Start

the drive on the wheels with the speed control lever

on the left side of the handle. Move the speed

control lever forward to increase the speed and

rearward to decrease the speed. (Fig. 37)

• Before you pull the product rearward, disengage the

drive and push the product forward approximately

10 cm.

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To stop the product

• To stop the engine, release the engine brake handle.

To remove the battery

To prevent accidental start of the engine, remove the

battery on model LC 347VI, LC 353VI when the product

is not in operation.

1. Press the lock buttons (A) and pull the battery out.

(Fig. 38)

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

• Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

808 - 004 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 347VI in the language / languages: All languages as an attachment in your email.

The manual is 4,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna LC 347VI Manual

Product: