733923
568
Zoom out
Zoom in
Previous page
1/576
Next page
每次使用 每月 每个季节
检查启动禁止器* X
确保本产品上的安全装置无故障* X
检查切割设备 X
检查切割防护盖* X
检查电机制动手柄* X
确保开/关按钮工作正常且无故障 X
检查电池是否损坏 X
检查电池电量 X
确保电池上的释放按钮工作正常并将电池锁入本产品中 X
检查电池充电器是否损坏,确保其工作正常。 X
检查电池和本产品之间的连接。还要检查电池与电池充电器之间的连接。 X
进行一般性检查
确保产品上的螺母和螺钉都已拧紧。
确保产品上的电缆不会损坏。
清洁产品
用清洁的干布擦净塑料部件。
请勿用水清洁本产品。水会进入电池或电机,并导致
短路或损坏本产品。
不要使用高压清洗机清洁产品。
不要直接用水冲洗马达。
用刷子清除树叶、草和污垢。
清洁电池和电池充电器
小心: 切勿用水清洁电池或充电器。
在将电池放入电池充电器之前,确保电池和电池充电
器清洁、干燥。
请使用压缩空气或软干布清洁电池端子。
请使用软干布清洁电池和电池充电器的表面。
润滑切割设备
警告: 为防止意外启动,将安全钥匙转至 0,
拆下电池,然后等待至少 5 秒钟。
警告: 维护切割设备时,请戴上保护手套。刀
片非常锋利,很容易割到手。
1. 检查切割设备是否有损坏或裂痕。务必更换损坏的切
割设备。
2. 检查刀片,查看是否损坏或变钝。
注释: 必须在磨利后使刀片保持平衡。让维修中心磨利、
更换和平衡刀片。如果您碰到障碍物导致本产品停止运
转,请更换损坏的刀片。让维修中心评估刀片可以磨利还
是必须更换。
卸下和更换刀片
1. 使用木块卡住刀片。 (圖 45)
2. 拆下刀片螺栓。
3. 拆下刀片。
4. 检查刀片支撑和刀片螺栓,查看是否有损坏。
5. 检查电机轴,确保其未弯曲。
6. 安装新刀片时,请将刀片的倾斜端指向切割防护盖的
方向。 (圖 46)
7. 确保刀片与电机轴中心对准。
8. 使用木块卡住刀片。安装弹簧垫片,并且用 23–28
Nm 扭矩拧紧螺丝和垫片。 (圖 47)
9. 用手拉住刀片旋转,确保刀片转动自如。
警告: 请佩戴耐磨手套。刀片非常锋利,
很容易割到手。
10. 启动本产品以测试刀片。如果刀片未正确安装,则本
产品中存在振动,或切割结果令人不满意。
568
890 - 002 - 21.12.2018
568


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 347iVX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 347iVX in the language / languages: All languages as an attachment in your email.

The manual is 6,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info