579199
7
Zoom out
Zoom in
Previous page
1/132
Next page
ENGLISH -
OPERATION
ENGINE ADJUSTMENTS (Fig.JI)
Refer to the engine manufacturer’s maintenance ma-
nual.
CAUTION:- Oil must be added to the
engine before use
STARTING THE ENGINE (Fig.J
II)
Once the machine has been set up properly, start the
engine as follows:
a)Operate the engine stop lever (14) to prepare the
engine for start, keep lever pressed against handle
while starting and using the machine (it operates the
engine brake).
b) Engines with primer system:
Press the fuel-enrichment pump (2) located on the car-
burettor 3 or 4 .semit
For further information and explanations, read carefully
the user instruction manual of the engine.
c) Start engine.
MANUAL STARTING: (While holding the engine stop
lever (14)).
Hold the engine start-grip (11) and pull the starter rope
gently until you feel the resistance caused by compres-
sion. Return the starter rope slowly then pull the handle
firmly towards you to it’s full extent.
ELECTRICAL S
TARTING: (While holding the engine
stop lever (14)).
Insert the plug (G) in the socket (H) on the engine.
Turn the ignition key (16).
CAUTION: The blade starts turning as soon
as the engine is started.
Keep the engine stop lever (14) depressed during machine
operation. When the lever is released, the engine stops.
MOWING
To cut the grass, push the lawn mower manually or insert
the automatic advance gear.
How to insert automatic advance (Fig. J
III): Lift up the
clutch handle (17 - 18) and keep it pressed in position.
CAUTION: Engage the gear only when the
engine is running.
How to disengage advance: Release the clutch han-
dle.
Before pulling the machine towards you, disengage the
drive and push the machine forward approx 10 cm.
4
ADJUSTMENT OF CLUTCH CABLE (for self-propelled versions only)
Important: If, when you press the clutch lever, the automatic advance gear does not engage, the clutch cable should
be adjusted by inserting the spring (P) in one of the subsequent holes in the plate (R) or in the hole “S” .
MAINTENANCE
Caution! Switch off the motor and disconnect
the spark plug before undertaking any mainte-
nance work.
The lawn mower must be checked by a SERVICE
DEALER.
Cleaning under the bodywork
With machine at a standstill and off.
- Attach fitting (22) on the deck to the water supply tap.
Turn on the tap.
- start up the motor (blade in rotation), allowing it to
warm up for a few minutes.
- at the end of cleaning switch off the motor, turn off the
tap, detach the tube from the deck connection.
For a four stroke engine, check the oil level and change
the oil when dirty. For further explanation, see ENGINE
INSTRUCTION BOOK.
Frequently check the mower and ensure that all grass
deposits are removed from beneath the deck.
Never clean the mower by pouring water over it: this may
seriously damage the electric start system.
Take care, the exhaust muffler may be very hot.
Frequently check the blade for damage.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 146S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 146S in the language / languages: All languages as an attachment in your email.

The manual is 14,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info