733985

Husqvarna LC 141iV Manual

18
Zoom out
Zoom in
Previous page
1/580
Next page
that are not approved cannot
get access to the product,
battery or battery charger.
Assembly
Introduction
WARNING: Before you assemble the
product, read the safety chapter.
WARNING: For model LC 141iV, LC 141i:
To prevent accidental start during assembly,
turn the safety key to 0, remove the battery
and wait at minimum 5 seconds.
For model LC 141C: To prevent accidental
start during assembly, disconnect the power
cord.
To assemble the handle
1. Align the holes in the handlebar with the holes in the
lower handle and attach the screws, washers and
knobs. Tighten the knobs fully. (Fig. 30)
2. Attach the cables to the handle with the cable
holders. (Fig. 31)
Note: Make sure that the tension in the cables is not
too high. A too high tension can cause damage to
the cable if the handle is folded to transport position.
3. Put the cables around the hook at the bottom of the
handle. (Fig. 32)
To adjust the handle height
1. Loosen the lower knobs. (Fig. 33)
2. Remove the knob, washer, and screw on the left and
the right side.
3. The handle can be set to 2 different heights. Put the
screw in one of the 2 holes on the left and the right
side. (Fig. 34)
4. Attach the screws, washers and knobs.
5. Move the knobs up in the direction of the handle until
they stop and you hear a click. Tighten the knobs
fully. (Fig. 35)
To assemble the grass catcher
1. Push the 2 transportation covers out and down. (Fig.
36)
2. Put the top part of the grass catcher onto the lower
part of the grass catcher. Attach the grass catcher
frame with the clips. (Fig. 37)
3. Lift the rear cover.
4. Attach the hooks on the grass catcher to the top
edge of the chassis. (Fig. 38)
To assemble the mulching-kit
1. Lift up the rear cover and remove the grass catcher.
2. Put the mulch plug into the grass discharge channel.
The mulch plug of type A is for LC 141i and
LC 141C. Type B is for LC 141iV. (Fig. 39)
3. Close the rear cover.
4. Replace the blade with the Combi blade, see
To
remove and replace the blade on page 22
.
Operation
Introduction
WARNING: Before you operate the product,
you must read and understand the safety
chapter.
Husqvarna Connect
Husqvarna Connect is a free app for your mobile device.
The Husqvarna Connect app gives extended functions
for your Husqvarna product:
• Extended product information.
• Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect
app to connect and register the product.
To set the product in operation position
If the handle is put in transport and storage position (see
To set the product in transport position on page 23
), do
the procedure that follows to put the handle in operation
position.
1. Lift the handle until the lower handle locks into
operation position. (Fig. 40)
18 919 - 003 - 23.10.2019
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LC 141iV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 141iV in the language / languages: All languages as an attachment in your email.

The manual is 7,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info