Manual Husqvarna LC 141C (page 21 of 560) (All languages)

733907

Zoom out

Zoom in

1/560

2. Connect the other end of the power cord for the

battery charger in an grounded mains socket. The

LED on the battery charger flashes green one time.

(Fig. 48 )

3. Put the battery in the battery charger. The green light

on the charger comes on when the battery is

correctly connected to the battery charger.(Fig. 49 )

4. When all LEDs on the battery have come on the

battery is fully charged. Charge the battery for

maximum 24 hours.

5. To disconnect the battery charger from the mains

socket, pull the plug, not the power cord.

6. Remove the battery from the battery charger.

Battery charging status

A Husqvarna Li-ion battery can be charged or used at all

charging levels. The battery is not damaged. A fully

charged battery will not decrease its charge when the

battery is left in the charger.

LED display

Charging status

LED 1 flashes 0%-25%

LED 1 is lit, LED 2 flashes 25%-50%

LED 1, LED 2 are lit, LED

3 flashes

50%-75%

LED 1, LED 2, LED 3 are

lit, LED 4 flashes

75%-100%

LED 1, LED 2, LED 3,

LED 4 are lit

Fully charged

To operate LC 141VLi and LC 141Li

To start the product

1. Put a charged battery in the battery compartment.

2. Turn the safety key to 1.(Fig. 50 )

3. Stay behind the product.

4. Press the ON/OFF button (A) on the control panel

and the green LED (B) comes on.(Fig. 51 )

5. Loosen the start inhibitor.(Fig. 52 )

6. Push the motor brake handle in the direction of the

handlebar.(Fig. 53 )

To use the drive on the wheels

• Model LC 141VLi. Pull the drive bail in the direction

of the handlebar to start the drive.(Fig. 54 )

• Press + and - on the control panel to set the drive

speed in 4 steps.(Fig. 55 )

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To use the SavE function

The product has a battery saving function (SavE) that

gives longer operation time.

1. Press the SavE button (A) to start the function. The

green LED comes on.(Fig. 56 )

2. Press the SavE button again to stop the function.

The green LED (B) goes out.

The SavE function stops automatically if the ground

conditions make it necessary to have a higher output.

The SavE function starts automatically when the ground

conditions lets it.

High load function

When the product cuts long or wet grass, the motor

automatically increases rpm. The motor goes back to

standard mode when high load is not necessary.

To stop the product

The product stops automatically if you do not operate it

for 10 minutes. Always turn the safety key to 0 before

you let the product out of view.

1. Release the motor brake handle to stop the motor.

(Fig. 57 )

2. Press the ON/OFF button (A) on the control panel

and the green LED (B) goes out.(Fig. 58 )

3. Open the battery lid and turn the safety key to 0.(Fig.

59 )

4. To remove the battery, press the 2 release buttons

and pull out the battery.(Fig. 60 )

5. Charge the battery if it is weak. For more

information, see

To charge the battery on page 20

To operate LC 141C)

To select an approved cable (LC 141C)

Note:

For the UK market, use only the 16M extension

cable that comes with the product. For all other markets,

refer to the information below.

If extension cables are used, these must comply with the

minimum cross-sections in the table below:

Voltage

Cable length Cross section

220-240V/ 50Hz Up to 20 m 1.5 mm

220-240V/ 50Hz 20–50 m 2.5 mm

• Mains cables and extension cables are available

from your local approved service agent for

Husqvarna outdoor products.

• Only use extension cables specifically designed for

outdoor use and which conform to one of the

following specifications: Ordinary rubber (60245 IEC

53), Ordinary PVC (60227 IEC 53) or Ordinary PCP

(60245 IEC 57)

• If the cable is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

71 - 005 - 18.05.2018

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LC 141C in the language / languages: All languages as an attachment in your email.

The manual is 6,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna LC 141C Manual

Product: