733931

Husqvarna LB 248S Manual

13
Zoom out
Zoom in
Previous page
1/356
Next page
WARNING: Use protective gloves. The
blade is very sharp and cuts can easily
occur.
11. Start the product to do a test of the blade. If the
blade is not correctly attached, there is vibration in
the product or the cutting result is unsatisfactory.
To do a check of the oil level
CAUTION: A too low oil level can do
damage to the engine. Do a check of the oil
level before you start the product.
1. Put the product on level ground.
2. Remove the oil tank cap with the attached dipstick.
3. Clean the oil from the dipstick.
4. Put the dipstick fully into the oil tank to give a correct
picture of the oil level.
5. Remove the dipstick.
6. Examine the oil level on the dipstick.
7. If the oil level is low, fill with engine oil and do a
check of the oil level again.
To replace the engine oil
WARNING: Engine oil is very hot directly
after the engine is stopped. Let the engine
become cool before you drain the engine oil.
If you spill engine oil on your skin, clean with
soap and water.
1. Operate the product until the fuel tank is empty.
2. Remove the ignition cable from the spark plug.
3. Remove the oil tank cap.
4. Put a container below the product to collect the
engine oil in.
5. Tilt the product to drain the engine oil from the oil
tank.
6. Fill with new engine oil of the type recommended in
Technical data on page 15
.
7. Do a check of the oil level. Refer to
To do a check of
the oil level on page 13
.
Battery (LB 348SI)
WARNING: A defective battery decreases
the safety of the product. Always use a
battery approved by the manufacturer.
The battery gives power to the electrical start and is a
safety device that prevents accidental start. Remove the
battery when you do not operate the product and when
you let it stay out of view.
To start the battery
You need to start the battery before the first time you
use it.
1. Put the battery into the charger, see
To charge the
battery on page 13
.
2. Wait until a minimum of 1 green lamp comes on,
approximately 10 seconds.
3. Attach the battery to the engine, see
Electrical start
(LB 348SI) on page 11
.
To charge the battery
If only 1 or 0 lamp indicators on the battery are on, it is
necessary to charge it. An empty battery is fully charged
in 1 hour. To charge for shorter periods of time does not
do damage to the battery.
1. Put the battery in the battery charger. (Fig. 36)
2. Connect the battery charger to a power socket,
220V, 50Hz.
Status for battery charge
LED display on the battery
Status
LED 1 flashes 0%-25%
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED 3 flashes 50%-75%
LED 1, LED 2, LED 3 are lit, LED 4
flashes
75%-100%
LED 1, LED 2, LED 3, LED 4 are lit Fully charged
Lamp indicator on the bat-
tery charger
Status
Constant red light The battery charges
Flashing red light The battery is too warm
and will start to charge
when the temperature is
correct
Constant green light The battery is fully charg-
ed
Flashing red and green
light
The battery is damaged
and must be replaced
To clean the air filter
1. Remove the air filter cover and remove the filter.
2. Hit the filter against a flat surface to make the
particles fall off.
CAUTION:
Do not use solvent or
compressed air to clean the air filter.
135 - 006 - 13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna LB 248S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna LB 248S in the language / languages: All languages as an attachment in your email.

The manual is 3,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info