518114
48
Zoom out
Zoom in
Previous page
1/52
Next page
Trouble
shooting
Always
start
by
checking
the
needle
Always
start
with
a
new
needle
as
soon
as
you
discover
that
a
stitch
is
not
what
you
expected.
Test
sew
on
a
scrap
of the
fabric
you
are
sewing.
Check
that
you
have
chosen
the
correct
needle
and
see
that
it
is
correctly
inserted.
See
page
15.
Unattractive
stitches
The
thread
tension
is
not
correct.
See
page
13.
Make
sure
that
the
thread
is
not
catching.
Certain
thread
spools
are
unsuitable
for
spooling
from
the
horizontal spool
pin.
Try
instead
with
the
vertical
spool
pin.
The
machine
may
be
incorrectly
threaded.
Be
sure
to
place
spool
holders
correctly.
The
correct
threading
is
shown
on
page
9.
Wrong
bobbin
thread.
It
should
be
of the
same thickness
as
the
upper
thread
except
when
sewing
embroidery.
The
needle
breaks
The
needle
can
strike
against
stitch
plate
and
break.
Change
the
needle.
See
page
15.
The
upper
thread
breaks
check
the
thread
spool
to
see
that
it
has
not caught
in
any
way.
The
needle
eye
may
have
sharp
edges
which
cut the
thread.
If
so,
change
the
needle.
See
page
15.
The
upper
thread
is
incorrectly
threaded.
See
page
9.
The
upper
thread
may
have
too
much tension.
Refer to
page
13.
The
hole
in
the
stitch
plate
may
be
chipped
and
have
sharp
edges.
We
recommend
that you
replace
it.
The
bobbin
thread
breaks
The
bobbin
thread
may
be
incorrectly
threaded.
See
page
12.
The
stitch
plate
hole
is
damaged.
See
“Upper
thread
breaks”.
Irregular
thread
tension
This
may
be
due
to
poor
quality
thread.
When
sewing
with
cotton
thread,
increase
the
thread
tension.
See
page
12.
Irregular
bobbin
winding
The
machine
is
not
correctly
threaded
for
bobbin
winding.
See
page
11.
The
fabric
puckers
The
upper
thread
tension
is
too
tight.
See
page
13
for
correct
thread
tension.
Use
the
correct presser
foot
as
recommended
by
the
infodisplay.
The
machine
does
not
feed
the
fabric
The
stitch
length
is
too
short.
Increase
stitch
length.
The
feed
teeth
may
be
lowered.
Raise
them
by
turning
the
dial
to
-—-.
See
page
15.
The
feed
teeth
are
full
of
dust
and
dirt.
Clean
with
the
brush.
See
page
47.
U
48
Ucer
Guide
Iris
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Iris at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Iris in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info