518114

Husqvarna Iris Manual

33
Zoom out
Zoom in
Previous page
1/52
Next page
Buttonhole
knife
The
knife
is
used
to
cut
buttonholes.
It
is
also
useful
for
removing
stitches
sewn
in
error.
Sewing
buttons
1.
Mark
the
fabric
where
the
button
is
to
be
located.
2.
Select
zigzag
3.
Lower
the
feed
teeth
with
the
dial.
See
page
15.
4.
Snap
off
the
presser
foot.
5.
Place
the
material
under
the
presser
foot
ankle.
6.
Place
the
button
on
marking
and
lower
the
presser
bar
so
that
the
presser
foot
ankle
is
between
the
holes
of
the
button
(see
picture).
7.
Hold
the
thread
ends
to
one
side.
Turn
the
handwheel
and
check
to
be
sure
that
the
needle
goes
into
the
left
hole
of
the
button.
8.
Touch
the
mirroring
button
to
check
that
the
needle
also
goes
into
the
right
hole.
9.
Sew
as
many
stitches
as
you
consider
necessary.
Button
wfth
a
shank
Use
the
clearance
plate
for
this
purpose.
Use
the
thin
end
when
sewing
buttons
on
light
fabrics,
the
thick
end
for
heavier
fabrics.
Place
the
plate
between
the
button
and
the
fabric.
Lower
the
presser
bar
and
sew
on
the
button.
Pull
the
threac.js
between
the
button
and
the
fabric.
Wind
the
threads
a
few
times
around
the
shank
and
tie
the
ends.
10.
Touch
STOP.
The
machine
will
then
tie
off
in
one
of
the
holes
and
stop.
11.Touch
STOP
to
cancel
it.
Move
to
the
next
pair
of
holes
or
the
next
button.
If
you
have
a
button
with
a
different
hole
spacing,
you
can
adjust
this
by
pressing
one
of
the
stitch
width
buttons
(+)
or
(-).
p
A
m
User’s
Guide
Iris
22
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Iris at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Iris in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info