Manual Husqvarna Huskystar 224 (page 11 of 56) (English)

518064

11

Zoom out

Zoom in

Previous page

1/56

Next page

9

Sewing Light

The sewing light is located behind the face

plate. To change the bulb, take the face

plate off the sewing machine by removing

the set screw.

Caution: Unplug the power supply

before changing the bulb and wait

until the bulb has cooled down before

touch ing it.

(1) Model 224 (12V, 5W)

To remove ........ Draw out slowly

To replace ........ Push in

(2) Model 219 (15W)

To remove ......... Push and twist to the

left.

To replace ......... Push and twist to the

right.

Dropping the Feed Teeth

* For button sewing and free motion

sewing, drop the feed teeth.

* When ﬁ nished sewing, raise the feed

teeth.

Drop feed lever is located to the back and

underneath the free arm bed.

1. To raise the feed teeth.

2. To drop the feed teeth.

1

2

(1)

(2)

Note: The feed teeth must always be up

for normal sewing.

1

How do I set my machine to zigzag
My machine only makes small stitches even when I change the length Submitted on 5-3-2022 at 21:36
Reply Report abuse
I can not replace a new needle. Difficult to find entrance Submitted on 19-2-2022 at 22:45
Reply Report abuse
The machine started bunching all the cotton on the underside of the material and would not progress. In the manual it suggests that lint might have collected, it had, so I cleaned this out thoroughly. I read troubleshooting in the manual and it mentioned the position of the feed teeth and the lever to the back and below the free arm bed, I slid this across and the teeth dropped but would not rise when I slid it back to the "raise feed teeth" position. It had no effect so now cannot use the machine. Can one repair this, if so, how? Thank you. Submitted on 8-12-2021 at 13:25
Reply Report abuse
the reverse is not working, am i missing a setting?
Submitted on 20-4-2020 at 06:58
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Husqvarna Huskystar 224 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskystar 224 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info