518064

Husqvarna Huskystar 224 Manual

4
Zoom out
Zoom in
Previous page
1/56
Next page
2
Name of parts (Model 224)
01. Bobbin winder stopper
02. Bobbin winder spindle
03. Extra spool pin mounting hole
04. Spool holder
05. Spool pin
06. Thread tension dial
07. Thread take-up lever
08. Pressure adjusting dial
09. Face plate
10. Thread cutter
11. Needle threader
12. Needle plate
13. Extension table
14. Hook cover plate
15. Hook cover plate release button
16. Up/down needle position
button
17. Reverse stitch button
18. Speed setting lever
19. Pattern selector dial
20. Stitch length dial
21. Pattern indicating window
22. Zigzag width control lever
23. Presser foot
24. Needle
25. Needle clamp screw
26. Foot holder
27. Thumb screw
28. Carrying handle
29. Handwheel
30. Feed balance dial
31. Power switch
32. Machine sockets
33. Drop feed lever
34. Free arm
35. Buttonhole lever
36. Presser foot lifter
01
020304
0506
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
… 4 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-huskystar-224

Reset search

  • How do I set my machine to zigzag
    My machine only makes small stitches even when I change the length Submitted on 5-3-2022 at 21:36

    Reply Report abuse

  • I can not replace a new needle. Difficult to find entrance Submitted on 19-2-2022 at 22:45

    Reply Report abuse

  • The machine started bunching all the cotton on the underside of the material and would not progress. In the manual it suggests that lint might have collected, it had, so I cleaned this out thoroughly. I read troubleshooting in the manual and it mentioned the position of the feed teeth and the lever to the back and below the free arm bed, I slid this across and the teeth dropped but would not rise when I slid it back to the "raise feed teeth" position. It had no effect so now cannot use the machine. Can one repair this, if so, how? Thank you. Submitted on 8-12-2021 at 13:25

    Reply Report abuse

  • the reverse is not working, am i missing a setting?
    Submitted on 20-4-2020 at 06:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskystar 224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskystar 224 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info