510458
13
Zoom out
Zoom in
Previous page
1/28
Next page
13
Changing thread
The following is an easy way to change threads:
1. Cut the thread in use near the spool, behind the guides on the
telescopic thread stand.
2. Remove the thread spool and place the new thread on the
spool pin.
3. Tie the end of the new thread to the end of the old thread.
Cut the thread tails to 2-3 cm in length and À rmly pull both
threads to test knot security.
4. Raise the presser foot.
5. First note tension dial settings and then turn the tension dials
down to “0”.
6. Pull the threads through the machine one at a time until the
knots are in front of the needle. If the threads do not pull
easily, check for tangles on thread guides or looping under
thread stand.
7. Cut the thread behind the knot and thread the needle.
8. Return tension dials to previous settings.
Note: When using standard thread spools, place the thread
unreeling disc as shown to prevent the thread from getting caught
on the edge of the spool.
Start sewing
1. When the machine is completely threaded, close the front
cover and bring all of the threads over the stitch plate and
slightly to the left under the presser foot.
2. Ensure that the upper blade moves against the lower blade
correctly by turning the handwheel slowly toward you. If the
blades are not moving correctly, check if there are any fabric
or waste thread stuck between the blades.
3. Hold the threads and apply a slight tension.
4. Turn the hand wheel toward you 2 or 3 complete turns to
start making a thread chain. Check if all threads wind around
the stitch À nger of the stitch plate. If the threads do not wind
around the À nger, make sure each thread is threaded correctly.
5. Continue holding the thread chain while pressing the foot
control. Sew until the chain is 5-8 cm in length.
6. Place fabric under the front of the presser foot and sew a test
sample. Guide the fabric slightly with your left hand while
sewing. Do not pull on the fabric as this may deÁ ect the
needle, causing it to break.
7. When you reach the end of the fabric, continue sewing while
drawing the À nished fabric gently backwards and to the
left. This is called chaining off. It prevents the threads from
coming undone and prepares for next sewing.
8. Cut off the thread chain 2-5 cm behind the presser foot using
the thread cutter on the left side of the machine. Pull the
threads around the thread cutter from the back, then toward
you.
Thread chain
Chaining off Thread cutter
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna HUSKYLOCK s15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna HUSKYLOCK s15 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna HUSKYLOCK s15

Husqvarna HUSKYLOCK s15 User Manual - German - 28 pages

Husqvarna HUSKYLOCK s15 User Manual - Dutch - 28 pages

Husqvarna HUSKYLOCK s15 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info