510458
8
Zoom out
Zoom in
Previous page
1/28
Next page
8
A
B
C
D
A
Disengage the movable upper cutter
Place the movable upper cutter in nonworking
position
1. Turn the hand wheel toward you until the upper cutter is
raised to the highest position.
2. Open the front cover.
3. Push the movable cutter holder to the right as far as it will go.
4. Turn the knob away from you until the cutter clicks into the
nonworking horizontal position (A).
Note: If the cutter stops in the up position;
- Turn the hand wheel toward you until the cutter clears the top
of the machine. Continue to rotate the cutter to the horizontal
position.
To place the movable upper cutter back in cutting
position
1. Open the front cover and push the movable cutter holder to
the right as far as it will go.
2. Turn the knob up and toward you until the cutter clicks into
the cutting position.
Note: Always have the cutter down in the cutting position when
sewing, because this machine must trim off any excess fabric to
form the stitch over the fabric edge.
Attaching the 2-thread overlock
converter
2-thread overlock stitches are sewn using one needle thread and
the lower looper thread. Before sewing, the two-thread converter
must be attached to the upper looper, so the machine will sew
with only two threads.
1. Open the front cover.
2. Bring the upper looper to its lowest position by turning the
handwheel toward you.
3. Insert the pin (A) of the converter in the hole (B) of the
upper looper.
4. Put the positioning rib (C) in contact with the upper edge of
the looper.
5. Insert the point (D) in the hole of the upper looper.
Removing the 2-thread overlock converter
1. Remove the point (D) from the hole of the upper looper and
remove the converter.
2. Put the the 2-thread converter back to the accessory storage.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna HUSKYLOCK s15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna HUSKYLOCK s15 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna HUSKYLOCK s15

Husqvarna HUSKYLOCK s15 User Manual - German - 28 pages

Husqvarna HUSKYLOCK s15 User Manual - Dutch - 28 pages

Husqvarna HUSKYLOCK s15 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info