610232
36
Zoom out
Zoom in
Previous page
1/44
Next page
3.
CARING
FOR
YOUR
MACHINE
REPLACING
MOVING
CUTTER
Should
it
become
necessary
to
replace
the
moving
cutter,
due
to
it
becoming
blunt,
apply
the
following
procedure.
NOTE:
You
should
not
need
to
replace
the
fixed
cutter,
which
is
made
of
a
special
hard
alloy
material.
FIRST
REMOVE
THE
POWER
PLUG
FROM
THE
SUPPLY
SOCKET-OUTLET.
1.
Swing
open
both
front
and
side
covers.
2.
Remove
the
old
cutter
by
loosening
the
screw
(A).
Using
the
small
brush
supplied
in
your
accessories,
clean
away
any
accumulation
of
lint
etc.
around
the
exposed
area.
(Fig.
1)
3.
Lower
the
shaft
(B)
to
its
lowest
position
by
turning
the
hand
wheel
towards
you
by
hand.
In
this
position,
fit
the
new
moving
cutter
by
replacing
screw
(A)
and
retighten,
ENSURING
THAT
THE
EDGE
OF
THE
MOVING
CUTTER
IS
APPROXIMATELY
0.5
mm
BELOW
THE
SURFACE
OF
THE
FIXED
CUTTER—see
inset
picture
Fig:2.
CHANGING
LIGHT
BULB
The
sewing
light
is
located
under
the
machine
arm,
as
shown,
and
illuminates
the
sewing
area
only.
DISCONNECT
MACHINE
FROM
THE
POWER
SUPPLY
BY
REMOVING
PLUG
FROM
SOCKET-
OUTLET.
DO
NOT
REPLACE
BULB
OF
MORE
THAN
15
WATTS
MAX.
To
change
bulb,
pull
down
light
cover,
push
the
bulb
in
slightly
and
turn
clockwise.
Remove
it
from
socket.
Push
in
new
bulb
and
turn
counter-clockwise.
Push
up
light
cover.
cutter
Highest
position
of
moving
cutter
Fig.
1
Lowest
position
of
moving
cutter
Fig.
2
34
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskylock 341 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 341 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info