610231

Husqvarna Huskylock 340D Manual

27
Zoom out
Zoom in
Previous page
1/42
Next page
01/23/2008
INSIDE
CORNERS
AND
ANGLES
Inside
corners
may
require
a
little
practice
prior
to
overlocking
your
finished
garment.
You
may
either
cut
your
fabric
to
desired
size
or
mark
your
fabric
and
carefully
follow
your
line
and
trim
off
excess.
For
example:
(Cut
to
size
materials)
1.
Align
the
fabric
edge
with
the
inside
edge
of
cutter.
2.
Overlock
stitch
to
the
inside
edge,
allowing
your
cutter
to
make
one
cut
into
the
inside
corner.
UNCUT
MATERIAL:
Follow
the
same
procedure,
but
you
must
carefully
follow
your
mark.
Always
consider
that
you
will
have
excess
cut-away
material
to
handle.
3.
CAUTION:
Your
cutter
is
approximately
4”
in
front
of
the
needle,
so
you
must
fold
your
material
away
from
the
cutter.
Sew
to
the
corner
and
stop.
4.
Raise
up
presser
foot
and
needle,
pivot
material,
align
the
fabric
edge
against
the
inside
edge
of
cutter.
5.
Slide
the
thread
off
the
seam
forming
tongue
of
needle
plate.
6.
Align
needle
to
form
a
square
corner
and
sew
the
balance
of
your
seam.
J4
inch
Ihie
Small
notch
1’
—
line
25
… 27 …


Need help? Post your question in this forum.

Forumrules
1

Forum

husqvarna-huskylock-340d

Reset search

  • I was gifted a 340D without power cord, today it arrived. I have oiled it and it was clean. I cannot get the handwheel to turn, it buzzes but will not engage, is there a special knob to aid in its moving? Submitted on 21-4-2022 at 23:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskylock 340D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 340D in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info