609920
32
Zoom out
Zoom in
Previous page
1/35
Next page
DL.E
PLATES
AS
OPTIONAL
ACCESSORIES
Two
additional
needle
plates
are
available
as
optional
accessories
from
your
dealer.
CHANGING
NEEDLE
PLATES
FiRST
DISCONNECT
MACHINE
POWER
SUPPLY
BY
REMOVING
FROM
SOCKET-OUTLET.
During
the
changing
operation
be
careful
to
keep
fingers
away
from
both
cutters.
‘.
Unthread
machine.
2.
Raise
needle
to
its
highest
point
by
turning
hand
wheel
towards
you
and
also
raise
presser
foot.
3.
Open
both
front
and
side
cover
plates.
4.
Take
off
needle
plate
in
use,
by
removing
screw
(B)
and
lifting
plate
up
from
guide
pin.
(A>.
5.
If
you
are
changing
a
wide
hem
needle
,olate
for
a
narrower
one
(e.
g.
from
3.5mm
to
narrow/rolled
hem
plate>,
you
may
omit
the
next
step
and
proceed
to
nos.
7
to
10.
6.
Loosen
screw
(G)
and
slide
moving
cutter
(H)
to
the
right
by
pushing
shaft
(E>,
hold
firmly
in
position
and
re-tighten
screw
(G).
7.
Loosen
the
two
screws
ID)
and
slide
fixed
cutter
(C)
to
the
right.
8.
Place
new
needle
plate
into
position
and
secure
with
screw
(B>.
9.
Slide
fixed
cutter
(C)
back
to
the
left
until
it
aligns
with
the
right
edge
of
the
new
needle
plate.
Narrow
stitch
(about
2mm)
and
rolled
hemming.
No.
11599
10.
Loosen
screw
lG)
and
the
spring-loaded
moving
cutter
(H>
will
automatically
return
to
the
correct
position.
Re-tighten
screw
(6)
at
the
same
time
pushing
slightly
the
small
shaft
(F>
to
the
right
as
indicated
by
the
arrow.
5mm
No.11598
FROM
PLUG
30
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Huskylock 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Huskylock 300 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info