609769
61
Zoom out
Zoom in
Previous page
1/84
Next page
Attaching the Embroidery/Darning
Foot U
1. Turn off the power switch to prevent accidents.
2. Turn the hand wheel toward you until the needle is at its
highest point.
3. Raise the presser foot.
4. Remove the presser foot and holder by removing the
presser foot screw (A).
5. Change the needle to an embroidery needle (B).
6. Attach the Embroidery/Darning Foot U to the presser
bar (C) so that the arm (D) of foot rides on the shaft (E)
of the needle clamp.
7. Attach the presser foot screw (A) and tighten it. For
easier access, lower the needle slightly.
To Hoop the Fabric
For the best embroidery results, place a layer of stabilizer
beneath the fabric. When hooping stabilizer and fabric make
sure that they are smooth and securely hooped.
1. Open the quick release (A) on the outer hoop and loosen
the screw (B). Remove the inner hoop. Place the outer
hoop on a firm flat surface with the screw on the lower
right (B). There is a small arrow in the center of the lower
edge of the hoop which will line up with a small arrow on
the inner hoop.
2. Place the stabilizer and fabric, with the right sides facing
up, on top of the outer hoop. Place the inner hoop on
top of the fabric with the small arrow at the bottom edge.
If you can see the hoop size in the lower part of the inner
hoop, you have attached it correctly.
3. Push the inner hoop firmly into the outer hoop.
4. Close the quick release (A). Adjust the pressure of the
outer hoop by turning the retaining screw (B). The fabric
should be taut in the hoop for the best results.
Note: When embroidering additional designs on the same fabric, open
the quick release, move the hoop to the new position on the fabric and
close the quick release. When changing type of fabric, you might need to
adjust the pressure using the retaining screw. Do not force the quick
release.
6 Embroidery Preparations 61
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna DESIGNER JADE 35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna DESIGNER JADE 35 in the language / languages: English as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna DESIGNER JADE 35

Husqvarna DESIGNER JADE 35 User Manual - French - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info