517460
12
Zoom out
Zoom in
Previous page
1/117
Next page
12
Learn your Designer I
Stitch Re-start. To start sewing your se-
lected stitch at the beginning of the stitch
without having to re-set any special set-
tings you have made.
STOP is used to conclude a stitch. Your
De sig ner I fastens the thread and stops
automatically when one stitch sequence
has been completed. The button lights
up when you touch it. STOP is cancelled
when you touch the button again or by
selecting a new stitch. The button light
will go out. The STOP function can be
programmed. It can also be used for one
color embroidery.
FIX is automatically activated when a
stitch is selected or when Thread Cutter
has been used. The button lights up while
FIX function is active. By touching the
lighted button the function can be turned
off. At the beginning – De sig ner I sews a
few tie off stitches and goes on with the
selected stitch. Touch FIX while sewing
– De sig ner I sews a few tie off stitches
and stops automatically. The FIX function
can be programmed.
Reverse – your Designer I sews in reverse
when this button is touched. The button
lights up. De sig ner I sews forwards when
the button is released and the light goes
out. The longest reverse stitch length is
3mm. For permanent reverse, touch the
button twice in quick succession before
starting to sew. The button will be lit up
and the De sig ner I sews in reverse until
you touch the button again to cancel.
Needle stop up/down. Touch this button
to move the needle down or up. The set-
ting of the needle stop po si tion is changed
at the same time. You can also tap the
foot control to raise or lower needle.
Touch + SPEED or - SPEED to increase or
decrease the sewing speed. Touch when
not sewing and a Pop-up menu on the
Color Touch Screen indicates the speed
set ting. Touch OK or start sewing and
the pop up goes out. You can change the
speed set ting while sewing but no Pop-up
will appear. All stitches in De sig ner I have
Function buttons
a pre-set, recommended sewing speed.
When you select a stitch, De sig ner I auto-
matically sets the correct sewing speed.
START/STOP. Touch this button to run
and stop the machine without the foot
control. Touch START/STOP to begin and
touch again to stop sewing.
Selective Thread Cutter. Touch the
button and De sig ner I cuts the top and
bobbin threads, raises the presser foot
and the needle to the up po si tion and
activates the FIX function. To cut before
the needle moves to the start position of
next stitch, touch Thread Cutter while the
machine is running. A fl ashing STOP will
indicate that a cut is requested. The Th-
read cutter function can be programmed.
Sensor Foot Lift up and extra lift.
Touch this button and the pres ser foot
and the needle will be lifted to up po-
si tion. Touch the button once more and
the pres ser and foot will raise to ex tra lift
to make it easy to get thick fabric under
the pres ser foot.
Sensor Foot Lift pivot. To simplify pla-
cing the fabric, touch this button. The
pres ser foot will be lowered to pivot po-
si tion.
Sensor Foot Lift down. Touch this but-
ton and the pres ser foot will be comple-
tely lowered and De sig ner I is fi rmly hol-
ding your work.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Designer I at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Designer I in the language / languages: English as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Designer I

Husqvarna Designer I User Manual - German - 117 pages

Husqvarna Designer I User Manual - Dutch - 117 pages

Husqvarna Designer I User Manual - French - 117 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info