517461
12
Zoom out
Zoom in
Previous page
1/117
Next page
12
Learn your Designer I
USB
Stitch Re-start. To start sewing your se-
lected stitch at the beginning of the stitch
without having to re-set any special set-
tings you have made.
STOP is used to conclude a stitch. Your
Designer I
USB
fastens the thread and stops
automatically when one stitch sequence
has been completed. The button lights
up when you touch it. STOP is cancelled
when you touch the button again or by
selecting a new stitch. The button light
will go out. The STOP function can be
programmed. It can also be used for one
color embroidery.
FIX is automatically activated when a
stitch is selected or when Thread Cutter
has been used. The button lights up while
FIX function is active. By touching the
lighted button the function can be turned
off. At the beginning –
Designer I
USB
sews
a few tie off stitches and goes on with the
selected stitch. Touch FIX while sewing
Designer I
USB
sews a few tie off stitches
and stops automatically. The FIX function
can be programmed.
Reverse – your
Designer I
USB
sews in
reverse when this button is touched. The
button lights up. Designer I
USB
sews for-
wards when the button is released and the
light goes out. The longest reverse stitch
length is 3mm. For permanent reverse,
touch the button twice in quick succession
before starting to sew. The button will be
lit up and the Designer I
USB
sews in re-
verse until you touch the button again to
cancel.
Needle stop up/down. Touch this button
to move the needle down or up. The set-
ting of the needle stop po si tion is changed
at the same time. You can also tap the
foot control to raise or lower needle.
Touch + SPEED or - SPEED to increase or
decrease the sewing speed. Touch when
not sewing and a Pop-up menu on the
Color Touch Screen indicates the speed
set ting. Touch OK or start sewing and
the pop up goes out. You can change the
speed set ting while sewing but no Pop-up
will appear.
Function buttons
All stitches in Designer I
USB
have a
pre-set, recommended sewing speed.
When you select a stitch, Designer I
USB
automatically sets the correct sewing
speed.
START/STOP. Touch this button to run
and stop the machine without the foot
control. Touch START/STOP to begin and
touch again to stop sewing.
Selective Thread Cutter. Touch the but-
ton and
Designer I
USB
cuts the top and
bobbin threads, raises the presser foot
and the needle to the up po si tion and
activates the FIX function. To cut before
the needle moves to the start position of
next stitch, touch Thread Cutter while the
machine is running. A fl ashing STOP will
indicate that a cut is requested. The Th-
read cutter function can be programmed.
Sensor Foot Lift up and extra lift.
Touch this button and the pres ser foot
and the needle will be lifted to up po-
si tion. Touch the button once more and
the pres ser and foot will raise to ex tra lift
to make it easy to get thick fabric under
the pres ser foot.
Sensor Foot Lift pivot. To simplify pla-
cing the fabric, touch this button. The
pres ser foot will be lowered to pivot po-
si tion.
Sensor Foot Lift down. Touch this but-
ton and the pres ser foot will be comple-
tely lowered and
Designer I
USB
is fi rmly
holding your work.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Designer I - USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Designer I - USB in the language / languages: English as an attachment in your email.

The manual is 7,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Designer I - USB

Husqvarna Designer I - USB User Manual - German - 118 pages

Husqvarna Designer I - USB User Manual - Dutch - 117 pages

Husqvarna Designer I - USB User Manual - French - 117 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info