517456
12
Zoom out
Zoom in
Previous page
1/40
Next page
12
Instruction book/Manual de instrucciones 315, 325, 335
Bobbin winding with
the machine threaded
Make sure that the presser foot is up and the
needle is in the highest position.
Note! Do not use a plastic presser foot when
bobbin winding.
1. Place your empty bobbin with the small mark
outwards on the bobbin spindle on the
front of the machine. Bring the bobbin spindle
down.
2. Pull the thread from the needle under the press-
ser foot and to the right over the thread guide
(c).
3. Start from above and wind a few turns of
thread around the bob bin. Cut off the thread
on the thread knife (d).
4. Press the foot control. When the bobbin win-
ding is fi nished, remove the bobbin, cut off the
thread and bring the bobbin spindle up.
Note! We do not recommend winding specialty th-
reads such as clear nylon or other stretchy threads
through the needle. Instead see ”Bobbin winding
– vertical spool pin”.
Bobbin winding –vertical
spool pin
1. Place an empty bobbin
with the mark out-
wards on the bobbin
spindle and bring it
down.
2. Place the large spool
holder under the thread
on the spool pin.
3. Bring the thread under the thread
guide (a) and over thread guide
(b), further under thread guide (c).
4. From above wind a few turns of thread
around the bobbin and into the knife.
5. As ”4.” above.
Asegúrese que el prensatelas esté elevado y que la
aguja esté en su posición superior.
N.B! No utilice un prensatelas de plástico al
bobinaje.
1. Colocar la canilla vacía en el eje del canil-
lero, en el frente de la máquina con la marca
circular hacia fuera. Conduzca el eje del
canillero hacia abajo.
2. Pasar el hilo de la aguja, por debajo del pie
prensatelas y hacia la derecha haciéndolo pasar
por encima del guía-hilo (c).
3. Después, comenzar por arriba y dar unas
cuantas vueltas al hilo en la canilla.Cortar el
hilo con el cortador (d).
4. Presionar sobre el pedal. Al terminar el bibina-
je saque la canilla, pasa el hilo por el cortador
y conduzca el eje del canillero hacia arriba.
N.B! No se debe bobinar a través de la aguja un
hilo de nylon u otro tipo de hilo muy elástico. Ver
”Devanado – porta-carrete vertical”.
Devanado de la canilla
Devanado –
porta-carrete vertical
1. Poner una canilla vacía
con la marca hacia
fuera sobre el eje del
canillero y condúzcalo
hacia abajo.
2. El disco grande se
coloque como zócalo.
Ponga una bobina sobre
el porta-carrete.
3.
Pasar el hilo debajo el guía-hilo (a) y encima el
guía-hilo (b) después debajo el guía-hilo (c).
4. Dar unas cuantas vueltas al hilo sobre la
canilla. Pasar el hilo por el corta-hilos y
cortarlo.
5. Como ”4., Devanado de la canilla”.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Daisy 325 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Daisy 325 in the language / languages: English as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info