Manual Husqvarna CTH171 (page 24 of 88) (English, German, Dutch, French, Italian, Spanish)

477567

Zoom out

Zoom in

1/88

214

To Assemble Bagger

NOTE: For ease of assembly, you may wish to obtain the

assistance of another person when putting the bagger to-

geth er.

• Holes in front bagger tube are at an angle. Place front

bagger tube against lower bagger tube and check for

proper hole alignment before assembling bolts.

• Assemble front and lower bagger tubes using four (4)

1/4 x 50,8mm carriage bolts and lock nuts supplied.

Tighten se cure ly.

• Slide front and lower bagger tube assembly into the bag-

ger assemby.

• Assemble front and upper bagger tubes using four (4)

1/4 x 50,8mm carraige bolts and lock nuts supplied.

Tighten se cure ly.

• Slip all the vinyl bindings over the bagger tubes

• Slide the bagger dump handle through the hole in the

bagger top, install the clevis pin and secure with retainer

spring.

• Push cap over end of bagger dump handle.

NOTE: For future use, the clevis pin may be removed in order

to use the handle to clear the chute in the event it has become

clogged.

Bagger adjustment

For proper bag function and appearance, it may be nec es -

sary to adjust the bagger assembly. There should be 6mm

(1/4")-9mm (3/8") gap between the bagger top and fender and

the bagger top surface should be even with the top surface

of the fender. To adjust bagger position:

Horizontal adjustment

• Slightly loosen the nuts securing the bagger RH and LH

hor i zon tal adjustment brackets. Loosen only enough so

the brackets keep their position, but allow them to be

moved.

• Move the brackets the amount forward or back ward you

wish the bag assembly to move. Retighten the nuts se-

curely.

Vertical adjustment

• Slightly loosen the nuts securing the vertical adjustment

brackets. Loosen only enough so the brackets keep their

position, but allow them to be moved.

• Move the brackets the amount up or down you wish the

bag assembly to move. Retighten the nuts securely.

• Reinstall the bagger as sem bly and check the bagger to

fender ﬁ t. If necessary, repeat the procedure until proper

ﬁ t is attained.

To convert to bagging, mulching or discharge

See "Sec tion 5" of this manual.

0259

02593

1. Front bagger tube

2. Lower bagger tube

3. 1/4 x 50,8mm Car riage

Bolts

4. 1/4 Lock nut

1. Front bagger tube

2. 1/4 x 50,8mm Car riage

Bolts

3. 1/4 Lock nut

4. Vinyl Binding

5. Dump handle tube

6. Clevis pin

7. Retainer spring

8. Cap

02329

1. Top Surfaces Even

2. Horizontal Adjustment Brack et

3. Vertical Adjustment Brack et

6MM (1/4") - 9MM (3/8")

1. Handle

2. Retainer Spring

3. Pin

4. Plug

To assemble and install mulcher plug

• Remove spring retainer and pin from handle.

• Insert plug into handle. Make sure that the letter "A" on

both the plug and handle are on the same side and that

they can both be seen from the top when laying on the

ground.

• Secure with pin and retainer spring provided. For in-

stal la tion see "To Convert Mower" in Section 5 of this

manual.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH171 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Husqvarna CTH171 Manual

Product: