585401
68
Zoom out
Zoom in
Previous page
1/84
Next page
68
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
BLADE REMOVAL
Raise mower to highest position to allow access to
blades.
Remove hex bolt, lock washer and flat washer securing
blade.
Install new or resharpened blade with trailing edge up
towards deck as shown.
IMPORTANT: To ensure proper assembly, center hole in
blade must align with star on mandrel assembly.
Reassemble hex bolt, lock washer and flat washer in
exact order as shown.
Tighten bolt securely (27-35 Ft. Lbs. torque).
IMPORTANT: Blade bolt is grade 8 heat treated
Für beste Mähergebnisse müssen die Messerbalken immer
opti mal geschliffen sein. Wechseln Sie verbogene oder
beschädigte Messerbalken sofort aus.
WECHSELN DER MESSERBALKEN:
Fahren Sie das Mähdeck in die höchste Position, um
Zugriff zu den Messerbalken zu bekommen.
Lösen Sie die Sechskantschraube, die Sicherungs-
scheibe und die Unterlegscheibe, die den Messerbalken
fixieren.
Montieren Sie den neuen bzw. den neu geschärften
Messerbalken, wobei die hintere (Hilfschneid-) Kante
wie abgebilAdet nach oben zur Plattform zeigen muß.
WICHTIG: Um eine richtige Montage zu gewährleisten, muß
die Zentrierbohrung des Messerbalkens mit der
Messeraufnahme übereinstimmen.
Montieren Sie nun in der beschriebenen Reihenfolge
die Sechskantschraube, die Sicherungsscheibe sowie
die Unterlegscheibe.
Ziehen Sie die Schrauben gut fest (Drehmoment: 27-37
Nm.)
HINWEIS: Die Sechskantschraube des Messerbalkens ist
wärmebehandelt.
Pour avoir une bonne qualité de coupe, il est indispensable
d'avoir des lames bien affûtées. Changer les lames
défectueuse ou tordues.
POUR RETIRER LES LAMES.
Relevez la machine sa position la plus haute pour avoir
accës aux lames coupantes.
Desserrer le boulon à tête hexagonale, le circlip et la
rondelle plate fixant la lame sur le moyeu.
Installer une nouvelle lame ou la lame d'origine réaffutée
avec le tranchant tourné vers le haut du carter comme
indiqué sur le dessin
ATTENTION: Pour que la lame soit bien montée, l'orifice
central en forme d'étiol de la lame doit être parfaitement
emboîté sur l'étoile du moyeu.
Remonter le boulon à tête hexagonale, le circlip et la
rondelle plate dans l'order exact, comme indiqué.
Resserer le boulon avec un couple de serrage de 3,7 à
4,9 mKg.
ATTENTION: Le boulon de lame a été traité thermiquement
-classe 8. Bien respecter le couple de serrage.
66
66
6
Para alcanzar resultados mejores las cuchillas de la
segadora hay que mantenerlos afilados. sustituya las
cuchillas torcidos y estropeados.
C'MO DESMONTAR LAS CUCHILLAS
Eleve la segadora hasta su posición más alta para
poder alcanzar las cuchillas.
Desentornille el tornillo de cabeza de seis facetas, la
arandela elastica (de resorte) y la arandela plana que
sujetan la cuchilla.
Monte la cuchilla nueva o afilada con el canto trasero
hacia arriba adjunto a la plataforma como indicado.
ATENCION: Para asegurar un montaje correcto el orificio
central de la cuchilla hay que ajustarlo a la estrella del
mandril.
Monte otra vez el tornillo de cabeza de seis facetas, la
arandela elastica y la arandela plana en sucesion
exacta como es indicado.
Apriete establemente el tornillo (momento de rotacion
27-35 Ft. Lbs.).
ATENCION: El tornillo de la cuchilla es de tratamiento
tèrmico-clase 8.
Per avere il migliore risultato di taglio, è necessario che le
lame siano ben affilate. Sostituirle se usurate o danneggiate.
RIMOZIONE DELLE LAME
Sollevare la macchina per avere accesso alle lame.
Disserrare il bullone a testa esagonale, la rondella
elastica e la rondella piatta che fissano la lama.
Montare una nuova lama o una lama con palettaura
posteriore rivolta verso il piatto, come indicato.
ATTENZIONE: Per assicurare un buon fissaggio centrale
della lama, è necessario che questa combaci perfettamente
con il mozzo.
Montare il nuovo bullone a testa esagonale, la rondella
elastica e la rondella piatta nell'ordine esatto, come
indicato.
Restringere bene il bullone di bloccaggio della lama
(coppia di serraggio: 27-35 ft./lbs)
ATTENZIONE: Il bullone di bloccaggio della lama è stato
sottoposto a trattamento termico di classe 8.
Voor de beste resultaten moeten de maaimessen scherp
gehouden worden. Vervang gebogen of beschadigde
messen.
MES VERWIJDEREN
Zet de maaier in de hoogste stand om bij de messen te
kunnen.
Verwijder de zeskantbout, de veerring, en vlakke ring
die het mes op zijn plaats houden.
Monteer een nieuw of geslepen mes waarbij het sleep
(hulp) mes omhoog naar het maaidek gericht moet zijn,
zie afbeelding.
BELANGRIJK: Om zeker te zijn van goede montage moet
het centrumgat in het mes passen met de ster op de mandrijn.
Bevestig de zeskantbout, veerring en vlakke ring weer
in precies dezelfde volgorde als op de afbeelding te zien
is.
Haal de bouten stevig aan (aandraaimoment 27-35 ft.
lbs.)
BELANGRIJK: De bout van het mes is warmtebehandeld
volgens klasse 8.
NL
Eng
F
Esp
Downloaded from www.Manualslib.com manuals search engine
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CTH160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH160 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info