477566

Husqvarna CTH151 Manual

77
Zoom out
Zoom in
Previous page
1/88
Next page
77
00598
“A”
01553
2
“A”
1
1
6
REGLAGE TRANSVERSAL
• Relever le carter de coupe au maximum.
• A partir du milieu de chaque extrémités latérales du carter
de coupe, mesurer la distance du bord du carter par rap-
port au sol .
• La distance (A) doit être la même des deux côtés à 6 mm
près.
• Si un réglage est nécessaire, ne l'effectuer que d'un seul
côté en se référant à l'autre côté.
• Abaisser ou soulever un côté du carter de coupe en
ajustant la position de l'écrou de réglage de ce côté.
REMARQUE : A trois tours complets de l'écrou de réglage
correspond une variation de la hauteur au-dessus du sol, du
carter de coupe, de 0,3 cm.
• Contrôler à nouveau la distance au sol après chaque
opération de réglage.
ADJUSTE DE LADO A LADO
• Levante la segadora a su posición más alta.
• A media distancia de ambos lados de la segadora, mida
la altura desde la parte inferior del extremo de la segadora
al suelo. La distancia “A” debe ser la misma o dentro de
6mm (1/4") de la una a la otra.
• Si el ajuste es necesario, haga el ajuste en un lado de la
segadora solamente.
• Levante un lado de la segadora por apretar la tuerca de
ajuste del várillaje de levantamiento en ese lado.
• Baje un lado de la segadora por desapretar la tuerca de
ajuste del várillaje de levantamiento en ese lado.
NOTA: Cada tres vueltas completas de la tuerca de ajuste cam-
biará la altura de la segadora en aproximadamente (1/8").
• Vuelva a revisar las medidas después del adjuste.
REGOLAZIONE FIANCO A FIANCO
• Alzare il tagliaerba nella posizione più alta.
• Sui punti centrali di entrabi i lati del tagliaerba, misurare
l'altezza dal bordo inferiore del tagliaerba al suolo. La
distanza “A” deve essere la stessa o diversa non più di
circa 6mm (1/4 di pollice).
• Se necessario, fare la regolazione su un solo lato del
tagliaerba.
• Per alzare un lato del tagliaerba, stringere il dado di rego-
lazione dell'articolazione di sollevamento su quel lato.
• Per abbassare un lato del tagliaerba, allentare il dado di
regolazione dell'articolazione di sollevamento su quel lato.
NOTA: Tre giri completi del dado di regolazione cambiano
l'altezza del tagliaerba di circa 3 mm (1/8 di pollice).
• Dopo aver fatto la regolazione, ricontrollare le misurazioni.
LINKS/RECHTS BIJSTELLEN
• Zet de maaimachine in de hoogste stand.
• Meet vervolgens in het midden tussen beide zijkanten van
de maaimachine de hoogte van de onderkant van de ma-
aimachine tot de grond. Afstand “A” moet ofwel hetzelfde
zijn, ofwel binnen 6 mm (1/4") van elkaar liggen.
• Indien bijstellen nodig is, mag dit slechts aan één kant
van de maaimachine gebeuren.
• Draai de bijstelmoer vaster aan de kant van de maaima-
chine die u hoger wilt instellen.
• Draai de bijstelmoer looser aan de kant van de maaima-
chine die u lager wilt instellen.
N.B.: Drei slagen van de bijstelmoer veranderen de hoogte
ongeveer 3 mm (1/8").
• Controleer na het bijstellen de hoogte opnieuw.
(1) Bottom edge of mower
(2) Lift link adjustment nut
(1) Unterkante des Mähwerks
(2) Hubstangen-Stellmutter
(1) Extrémités du carter de coupe
(2) Ecrou de réglage du bras de suspension arrière
(1) Parte inferior de la esquina de la segadora
(2) Tuerca de ajuste del várillaje de levantamiento
(1) Bordo inferiore del tagliaerba
(2) Dado di regolazione dell'articolazione di sollevamento
(1) Onderkant van de maaimachine
(2) Bijstelmoer
SIDE-TO-SIDE ADJUSTMENT
• Raise mower to highest position.
• At the midpoint of both sides of mower, measure height
from bottom edge of mower to ground. Distance “A” should
be the same or within 6mm (1/4") of each other.
• If adjustment is necessary, make adjustment on one side
of mower only.
• To raise one side of mower, tighten lift link adjustment nut
on that side.
• To lower one side of mower, loosen lift link adjustment
nut on that side.
NOTE: Three full turns of adjustment nut will change mower
height about 1/8".
• Recheck measurements after adjusting.
SEITLICHE EINSTELLUNG
• Das Mähwerk auf die höchste Position einstellen.
• Auf beiden Seiten des Mähwerks in der Mitte den Abstand
von der Unterkante des Mähwerks zum Boden messen.
Der Abstand “A” sollte auf den beiden Seiten um höchstens
6 mm (1/4') voneinander abweichen.
• Falls eine Einstellung notwendig sein sollte, die Einstel-
lung nur auf einer Seite des Mähwerks vornehmen.
• Um eine Seite des Mähwerks anzuheben, die Hubstan-
gen-Stellmutter auf der jeweiligen Seite festziehen.
• Um eine Seite des Mähwerks abzusenken, die Hubstangen
-Stellmutter auf der jeweiligen Seite lösen.
HINWEIS: Drei volle Umdrehungen der Stellmutter verändern
die Höhe des Mähwerks um etwa 3 mm (1/8").
• Nach der Einstellung die Abstände erneut prüfen
… 77 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CTH151 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CTH151 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info