40855

Husqvarna CT135 Manual

69
Zoom out
Zoom in
Previous page
1/84
Next page
69
WARNING!
Do not forget to tighten the lock nut after completing adjust-
ment.
WARNUNG!
Nicht vergessen, die Sicherungsmutter nach durchgeführter
Einstellung anzuziehen.
ATTENTION!
Ne pas oublier de serrer l’écrou de verrouillage après le
réglage.
ADVERTENCIA!
Después del ajuste, no olvidarse de apretar la contratuerca.
PERICOLO!
Dopo la regolazione ristringere il dado di bloccaggio.
WAARSCHUWING
Vergeet niet de moeren aan te draaien na het bijstellen.
38mm
2
1
Brakes
The brakes are located inside the right rear wheel. The wheel
should be dismantled for best access.
• Press down the clutch/brake pedal and engage the
parking brake.
Bremse
Die Bremse sitzt innerhalb des rechten Hinterrades. Für
beste Zugänglichkeit ist das Rad auszubauen.
• Kupplungs-/Bremspedal durchtreten und die
Feststellbremse einschalten.
Reglage du Frein
Le frein se situe à l'avant de la roue arrière côté droit. La roue
doit être déposée pour avoir une bonne accessibilité.
• Avant toute intervention enfoncer la pédale de frein/
embrayage et engager le frein de parking.
Freno
El freno se halla por dentro de la rueda posterior derecha.
Esta puede desmontarse a fin de mejorar la accesibilidad.
• Apretar el pedal de embrague/freno y acoplar el freno de
estacionamiento.
Freno
Il freno è montato dietro la ruota posteriore destra. Si consiglia
di smontare la ruota.
• Premere il pedale freno/frizione e inserire il freno di
parcheggio
Rem
De rem zit aan de binnenkant van het rechter achterwiel. Om
er goed bij te kunnen komen, dient het wiel te worden gemon-
teerd.
• Druk de koppelings/rempedaal in en trek de parkeerrem
aan.
NL
Eng
F
Esp
NL
Eng
F
Esp
1. Measure the distance between the brake lever and the
adjuster nut.
2. The distance should be 38mm (1.5").
3. Adjust the distance if necessary by first loosening the
lock nut (2) and then adjusting with the nut (1).
1. Abstand zwischen Bremshebel und Stellmutter messen.
2. Der Abstand soll 38mm betragen.
3. Den Abstand wenn erforderlich einstellen, indem zuerst
die Sicherungsmutter (2) gelöst und danach die Mutter
(1) verstellt wird.
1. Mesurer la distance entre le levier de frein et l'écrou de
réglage.
2. La disstance doit être de 38mm.
3. Si nécessaire, ajuster la distance en commençant par
dévisser l'écrou de verrouillage (2) puis en réglant avec
l'écrou (1).
1. Medir la separación entre la palanca de freno y la tuerca
de ajuste.
2. La distancia ha de ser de 38mm.
3. En caso necesario ajustar la separación quitando
primero la contratuerca (2) y ajustando después con la
tuerca (1).
1. Misurare la distanza tra la leva del freno e il dado di
regolazione.
2. La distanza deve essere di 38mm.
3. Se necessario regolare allentando il dado (2) e agendo
poi sul dado (1).
1. Meet de afstand tussen de remnokas en de stelmoer.
2. De afstand dient 38mm te zijn.
3. Stel zonodig de afstand bij, door eerst borgmoer (2) los
te draaien en daarna bijstellen met stelmoer (1).
NL
Eng
F
Esp
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna CT135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna CT135 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info