819066
47
Zoom out
Zoom in
Previous page
1/60
Next page
7.4 LED indicator lamps on the charging station
For a fully functional installation, the indicator lamps in the charging station must show a solid or flashing green light. If
another color shows, follow the troubleshooting guide below.
There is more help on www.husqvarna.com. If you still need help, speak to your approved servicing dealer.
Light Status
Green solid light Good signals.
Green flashing light The signals are good and
ECO mode
is activated. Refer to
ECO mode on page 28
.
Red flashing light Interruption in the charging station’s antenna. Speak to your approved servicing
dealer.
Red solid light Fault in the circuit board or incorrect power supply in the charging station. The
fault must be correct by an authorized service technician. Speak to your approved
servicing dealer.
7.5 Symptoms
If the product does not operate correctly, refer to the symptoms table below.
Symptoms Cause Action
The product cannot go into
the charging station.
The charging station is not put on a level
surface.
Put the charging station on level surface.
Refer to
To examine where to put the
charging station on page 14
.
The charging station is put too far from
the work area.
Make a new work area or move the
charging station.
The product operates at the
incorrect time.
The time and date of the product must be
set.
Set the time and date. Refer to
Time &
date on page 28
.
The time and date of the product is not
set correctly.
The start and stop time for operating are
incorrect.
Change the schedule settings. Refer to
Schedule on page 27
.
There is vibration in the prod-
uct.
The cutting system is not in balance be-
cause of damaged blades.
Examine the blades and screws and re-
place them if it is necessary. Refer to
Re-
placement of the blades and blade discs
on page 36
.
The cutting system is not in balance be-
cause of too many blades in the same
position.
Make sure that only 1 blade is attached
to each screw.
Blades of different thickness are installed
on the product.
Examine if the blades are of different
thickness and replace the blades if nec-
essary.
The product operates, but the
blade disc does not rotate.
The product goes to the charging station. Usual operation for the product. The
blade disc does not rotate when the
product goes to the charging station.
1691 - 007 - 22.12.2023 Troubleshooting - 47
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Ceora 544 EPOS - 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Ceora 544 EPOS - 2024 in the language / languages: English as an attachment in your email.

The manual is 9.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Ceora 544 EPOS - 2024

Husqvarna Ceora 544 EPOS - 2024 User Manual - German - 64 pages

Husqvarna Ceora 544 EPOS - 2024 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info