733794
57
Zoom out
Zoom in
Previous page
1/64
Next page
Contents
1 Introduction
1.1 Support.......................................................3
1.2 Product description.....................................3
1.3 Automower® Connect.................................3
1.4 Product overview .......................................4
1.5 Symbols on the product..............................5
1.6 Symbols on the battery...............................6
1.7 General safety instructions.........................6
2 Safety
2.1 IMPORTANT. READ CAREFULLY
BEFORE USE. KEEP FOR FUTURE
REFERENCE................................................. 11
2.2 Safety definitions...................................... 12
2.3 Safety instructions for operation...............12
3 Installation
3.1 Introduction - Installation.......................... 16
3.2 Main components for installation..............16
3.3 General preparations................................16
3.4 Before the installation of the wires........... 16
3.5 Installation of the product......................... 21
3.6 To put the wire into position with stakes...24
3.7 To bury the boundary wire or the
guide wire....................................................... 24
3.8 To extend the boundary wire or the
guide wire....................................................... 24
3.9 After the installation of the product...........25
3.10 Automower® Connect.............................25
3.11 To start the product for the first time...... 26
3.12 Settings in Automower® Connect...........27
4 Operation
4.1 To switch on the product.......................... 32
4.2 Operating modes......................................32
4.3 To stop the product.................................. 33
4.4 To switch off the product.......................... 33
4.5 To charge the battery............................... 33
4.6 To adjust the cutting height with
Automower® Connect.....................................33
5 Maintenance
5.1 Introduction - maintenance.......................35
5.2 Clean the product..................................... 35
5.3 Replace the blades...................................36
5.4 To replace the top covers.........................37
5.5 Battery...................................................... 39
5.6 Winter service...........................................39
6 Troubleshooting
6.1 Introduction - troubleshooting...................41
6.2 Fault messages........................................ 41
6.3 Information messages.............................. 48
6.4 Indicator lamp in the charging station.......49
6.5 Symptoms................................................ 50
6.6 Find breaks in the loop wire..................... 51
7 Transportation, storage and disposal
7.1 Transportation.......................................... 54
7.2 Storage.....................................................54
7.3 Disposal....................................................54
8 Technical data
8.1 Technical data.......................................... 56
8.2 Registered trademarks............................. 58
9 Warranty
9.1 Warranty terms.........................................59
10 EC Declaration of Conformity
10.1 EC Declaration of Conformity.................60
21427 - 002 - 20.12.2019
1 Introduction
Serial number:
PIN code:
The serial number is on the product rating plate and on the product carton.
Use the serial number to register your product on www.husqvarna.com.
1.1 Support
For support about the product, speak to your
Husqvarna servicing dealer.
1.2 Product description
Note: Husqvarna regularly updates the
appearance and function of the products. Refer
to
Support on page 3
.
The product is a robotic lawn mower. The product
has a battery power source and cuts the grass
automatically. It continuously alternates between
mowing and charging. The movement pattern is
random, which means that the lawn is mowed
evenly and with less wear. The boundary wire
and the guide wire controls the movement of the
product within the work area. Sensors in the
product senses when it is approaching the
boundary wire. The front of the product always
passes the boundary wire by a specific distance
before the product turns around. When the
product hits an obstacle or approaches the
boundary wire the product selects a new
direction.
The operator selects the operation settings in
Automower® Connect app. The app shows the
selected and possible operation settings, and the
operation mode of the product.
1.2.1 Mowing technique
The product is emission free, easy to use and
saves energy. The frequent cutting technique
improves the grass quality and decreases the
use of fertilizers. Collection of grass is not
necessary.
1.2.2 Find the charging station
The product operates until the battery is low, then
it starts to go to the charging station. The product
has 3 search methods to find the charging
station. Refer to
To find the charging station on
page 28
.
1.3 Automower® Connect
Automower® Connect is a mobile application that
makes it possible to select the operation settings
remotely. Refer to
Automower® Connect on page
25
.
1427 - 002 - 20.12.2019 Introduction - 3
9. START button
10. Front wheels
11. Rear wheels
12. Battery cover
13. Rear chassis box with electronics, motors
and battery
14. LED for operation check of the charging
station and boundary wire
15. Charging station
16. Contact strips
17. Skid plate
18. Blades
19. Front chassis box with electronics and
motors
20. Rating plate (incl. product identification
code)
21. Blade disc
22. Power supply (the appearance of the power
supply may differ depending on market)
23. Low voltage cable
24. Screws for securing the charging station
25. Measurement gauge for help when installing
the boundary wire (the measurement gauge
is broken loose from the box)
26. Operator’s Manual and Quick Guide
27. Cable markers
28. Extra blades
29. Alarm decal
30. Loop wire for boundary loop and guide wire
1
31. Couplers for loop wire 2
32. Stakes3
33. Connector for the loop wire 4
1.5 Symbols on the product
These symbols can be found on the product.
Study them carefully.
WARNING: Read the
user instructions before
operating the product.
WARNING: Disable the
product before working on
or lifting the product.
WARNING: Keep a safe
distance from the product
when operating. Keep
your hands and feet away
from the rotating blades.
WARNING: Do not ride
on the product. Never put
your hands or feet close
to or under the product.
Never use a high-pres-
sure washer or even run-
ning water to clean the
product.
Use a detachable power
supply as defined on the
rating label next to the
symbol.
This product conforms to the
applicable EC Directives.
Noise emission to surroundings. The
product’s emissions are set out in
Technical data on page 56
and on the
rating plate.
It is not permitted to dispose this
product as normal household waste.
Ensure that the product is recycled in
accordance with local legal
requirements.
1Is a part of the Installation kit which is purchased separately.
2Refer to note 1
3Refer to note 1
4Refer to note 1
1427 - 002 - 20.12.2019 Introduction - 5
1.7.1 Menu structure overview 1
Operation
Cutting time
Low High
Weather timer
Schedule
Edit
Overview Schedule settings
Cutting height
Cutting height
Change current
Schedule settings
Add new
Schedule settings
ECO mode
Medium
1427 - 002 - 20.12.2019 Introduction - 7
1.7.4 LED status indicator
LED indication Status
Green In operation
Blue Parked
Red Error
Yellow Paused/stopped
Flashing yellow PIN code needed
Pulsating green/blue Charging in progress
Flashing green/blue Push the ON/OFF button
to confirm start of opera-
tion
Flashing green, low-
frequent
Inactive
White Switching off
10 - Introduction 1427 - 002 - 20.12.2019
2 Safety
2.1 IMPORTANT. READ CAREFULLY
BEFORE USE. KEEP FOR FUTURE
REFERENCE
The operator is responsible for accidents or hazards occurring to
other people or property.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities (that
could affect a safe handling of the product), or lack of experience
and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Local regulations
may restrict the age of the operator. Cleaning and maintenance
shall not be made by children without supervision.
Never connect the power supply to an outlet if the plug or cord is
damaged. Worn or damaged cord increase the risk of electric
shock.
Only charge the battery in the included charging station. Incorrect
use may result in electric shock, overheating or leaking of
corrosive liquid from the battery. In the event of leakage of
electrolyte, flush with water/neutralizing agent. Seek medical help if
it comes in contact with the eyes.
Use only original batteries recommended by the manufacturer.
Product safety cannot be guaranteed with other than original
batteries. Do not use non-rechargeable batteries.
The appliance must be disconnected from the supply mains when
removing the battery.
1427 - 002 - 20.12.2019 Safety - 11
WARNING: The product
can be dangerous if used
incorrectly.
WARNING: Do not use
the product when
persons, especially
children, or animals, are
in the work area.
WARNING: Keep your
hands and feet away
from the rotating blades.
Never put your hands or
feet close to or under the
product when the motor
is running.
WARNING: In the event
of an injury or accident
seek medical help.
2.2 Safety definitions
Warnings, cautions and notes are used to point
out specially important parts of the manual.
WARNING: Used if there is a risk of
injury or death for the operator or
bystanders if the instructions in the
manual are not obeyed.
CAUTION: Used if there is a risk of
damage to the product, other materials
or the adjacent area if the instructions
in the manual are not obeyed.
Note: Used to give more information that is
necessary in a given situation.
2.3 Safety instructions for operation
2.3.1 Use
The product may only be used with the
equipment recommended by the
manufacturer. All other types of use are
incorrect. The manufacturer’s instructions
with regard to operation/maintenance must
be followed precisely.
The product may only be operated,
maintained and repaired by persons that are
fully conversant with its special
characteristics and safety regulations.
Please read the Operator’s Manual carefully
and make sure you understand the
instructions before using the product.
It is not permitted to modify the original
design of the product. All modifications are
made at your own risk.
Warning signs shall be placed around the
work area of the product if it is used in public
areas. The signs shall have the following
text: Warning! Automatic lawn mower! Keep
away from the machine! Supervise children!
WARNING!
Automatic lawnmower!
Keep away from the machine!
Supervise children!
I am a robotic lawnmower and I work here quietly
to keep the lawn in perfect condition.
I work 24/7 independently of weather conditions and do it
without releasing any exhaust emissions.
Stay a while and enjoy my work,
but please let me work in peace.
12 - Safety 1427 - 002 - 20.12.2019
Use the park function or switch off the
product when persons, especially children or
pets, are in the work area. Refer to
To
switch off the product on page 33
. It is
recommended to program the product for
use during hours when the area is free from
activity, e.g. at night. Consider that certain
species, e.g. hedgehogs, are active at night.
They can potentially be harmed by the
product. Refer to
Schedule on page 27
.
Check that there are no foreign objects such
as stones, branches, tools or toys on the
lawn. If the blades hit foreign objects the
blades can be damaged. Always switch off
the product before clearing a blockage.
Inspect the product for damage before
staring the product again. Refer to
To switch
off the product on page 33
.
If the product starts to vibrate abnormally.
Always switch off the product and inspect for
damage before staring the product again.
Refer
To switch off the product on page 33
.
Switch on the product according to the
instructions. When the product is switched
on; make sure to keep your hands and feet
away from the rotating blades. Never put
your hands and feet under the product.
Never touch moving hazardous parts, such
as the blade disc, before it has come to a
complete stop.
Never lift up the product or carry it around
when it is switched on.
The product must never be allowed to
collide with persons or other living creatures.
If a person or other living creature comes in
the way of the product, it shall be stopped
immediately. Refer to
To stop the product on
page 33
.
Do not put anything on top of the product or
its charging station.
Do not allow the product to be used with a
defective guard, blade disc or body. Neither
should it be used with defective blades,
screws, nuts or cables. Never connect a
damaged cable, or touch a damaged cable
before it is disconnected from the supply.
Do not use the product if the STOP button
does not work.
Always switch off the product when it is not
in use. The product can only start when the
correct PIN code has been entered.
The product must never be used at the
same time as a sprinkler. Use the
Schedule
function so the product and sprinkler never
run simultaneously. Refer to
Schedule on
page 27
.
Husqvarna does not guarantee full
compatibility between the product and other
types of wireless systems such as remote
controls, radio transmitters, hearing loops,
underground electric animal fencing or
similar.
The built-in alarm is very loud. Be careful,
especially if the product is handled indoors.
Metal objects in the ground (for example
reinforced concrete or anti-mole nets) can
result in a stoppage. The metal objects can
cause interference with the loop signal
which then can lead to a stoppage.
Operation and storage temperature is 0-50
°C / 32-122 °F. Temperature range for
charging is 0-45 °C / 32-113 °F. Too high
temperatures might cause damage to the
product.
2.3.2 Battery safety
WARNING: Lithium-ion batteries can
explode or cause fire if disassembled,
short-circuited, exposed to water, fire,
or high temperatures. Handle carefully,
do not dismantle, open the battery or
use any type of electrical/mechanical
abuse. Avoid storage in direct sunlight.
For more information about the battery, refer to
Battery on page 39
1427 - 002 - 20.12.2019 Safety - 13
2.3.3 How to lift and move the product
WARNING: The product must be
switched off before you lift it. The
product is switched off when the LED
status indicator is not lit.
CAUTION: Do not lift the product when
it is parked in the charging station. It
can damage the charging station
and/or the product. Push the STOP
button and pull the product out of the
charging station before lifting it.
To safely move from or within the work area:
1. Push the STOP button to stop the product.
2. Enter the PIN code if required.
3. Push the ON/OFF button for 3 seconds to
switch off the product.
4. Make sure that the LED status indicator is
not lit.
5. Carry the product by the lifting handle.
2.3.4 Maintenance
WARNING: The product must be
switched off before it is turned upside
down.
The product must be switched off
before any maintenance is done.
CAUTION: Never use a high-pressure
washer or even running water to clean
the product. Never use solvents for
cleaning.
WARNING: Use the plug to disconnect
the charging station before any
cleaning or maintenance of the
charging station or the loop wire.
Inspect the product each week and replace any
damaged or worn parts. Refer to
Maintenance on
page 35
.
14 - Safety 1427 - 002 - 20.12.2019
2.3.5 In the event of a thunderstorm
To reduce the risk of damage to electrical
components in the product and the charging
station, we recommend that all connections to the
charging station are disconnected (power supply,
boundary wire and guide wire) if there is a risk of
a thunderstorm.
1. Mark the wires to simplify reconnecting. The
charging station’s connections are marked
AR, AL and G1, G2, G3.
2. Disconnect all connected wires and the
power supply.
3. Connect all the wires and the power supply
if there is no longer a risk of thunder. It is
important that each wire is connected to the
right place.
1427 - 002 - 20.12.2019 Safety - 15
3 Installation
3.1 Introduction - Installation
WARNING: Read and understand the
safety chapter before you install the
product.
CAUTION: Use original spare parts
and installation material.
Note: Refer to www.husqvarna.com for more
information about installation.
3.2 Main components for installation
The installation involves the following
components:
A robotic lawn mower that mows the lawn
automatically.
A charging station, which has 3 functions:
To send control signals along the
boundary wire.
To send control signals along the guide
wire so that the product can be send to
specific remote areas in the garden and
can find its way back to the charging
station.
To charge the product.
A power supply, which is connected to the
charging station and a 100-240V wall
socket.
Loop wire, which is laid around the work
area and around objects and plants that the
product must not run into. The loop wire is
used both as boundary wire and guide wire.
3.3 General preparations
CAUTION: Holes with water in the
lawn can cause damage to the
product.
Note: Read through the Installation chapter
before beginning the installation. How the
installation is done affects how the product
performs. It is therefore important to plan the
installation carefully.
Make a blueprint of the work area and
include all obstacles. This makes it easier to
see the ideal positions for the charging
station, the boundary wire and the guide
wire.
Make a mark on the blueprint where to put
the charging station, the boundary wire and
the guide wire.
Make a mark on the blueprint where the
guide wire connects to the boundary wire.
Refer to
To install the guide wire on page
23
.
Fill in holes in the lawn.
Cut the grass before you install the product.
Make sure that the grass is maximum 10
cm / 4 in.
Note: The first weeks after installation the
perceived sound level when cutting the grass
may be higher than expected. When the product
has cut the grass for some time, the perceived
sound level is much lower.
3.4 Before the installation of the wires
You can select to attach the wires with stakes or
bury them. You can use the 2 procedures for the
same work area.
Bury the boundary wire or the guide wire if
you are going to use a dethatcher on the
work area. If not, attach the boundary wire
or guide wire with stakes.
3.4.1 To examine where to put the charging
station
Keep a minimum 3 m / 10 ft. of free space in
front of the charging station.
Keep a minimum of 1.5 m / 5 ft. of free
space to the right and to the left of the
charging station.
Put the charging station near a power outlet.
Put the charging station on a level surface.
16 - Installation 1427 - 002 - 20.12.2019
max. 5 cm / 2"
max. 5 cm / 2"
Put the charging station in the largest open
section of the work area.
Put the charging station in an area without
an irrigation system.
Put the charging station in an area with
protection from the sun.
If the charging station is installed on an
island, make sure to connect the guide wire
to the island. Refer to
To make an island on
page 19
.
3.4.2 To examine where to put the power
supply
WARNING: Do not cut or extend the
low-voltage cable. There is a risk of
electrical shock.
CAUTION: Make sure that the blades
on the product do not cut the low-
voltage cable.
CAUTION: Do not put the low-voltage
cable in a coil or below the charging
station plate. The coil causes
interference with the signal from the
charging station.
Put the power supply in an area with a roof
and protection from the sun and rain.
Put the power supply in an area with good
airflow.
Use a residual-current device (RCD) when
you connect the power supply to the power
outlet.
Low-voltage cables of different lengths are
available as accessories.
3.4.3 To examine where to put the
boundary wire
CAUTION: If the work area is adjacent
to water bodies, slopes, precipices or a
public road, the boundary wire must
have a protective wall. The wall must
be minimum 15 cm / 6 in. in height.
CAUTION: Do not let the product
operate on gravel.
CAUTION: Do not make sharp bends
when you install the boundary wire.
CAUTION: For careful operation
without noise, isolate all obstacles
such as trees, roots and stones.
The boundary wire should be put as a loop
around the work area. Sensors in the product
senses when the product approaches the
boundary wire, and the product selects another
direction.
To make the connection easier between the
guide wire and the boundary wire, it is
recommended to make an eyelet where the guide
wire will be connected. Make the eyelet with
approximately 20 cm / 8 in. of the boundary wire.
1427 - 002 - 20.12.2019 Installation - 17
Note: Make a blueprint of the work area before
you install the boundary wire and guide wire.
D
E
B
C
F
A
Put the boundary wire around all of the work
area (A). Adapt the distance between the
boundary wire and obstacles.
Put the boundary wire 35 cm / 14 in. (B)
from an obstacle that is more than 5 cm / 2
in. high.
35 cm /14
"
> 5 cm / 2
"
Put the boundary wire 30 cm / 12 in. (C)
from an obstacle that is 1-5 cm / 0.4-2 in.
high.
1-5 cm / 0.4 - 2"
30 cm / 12"
Put the boundary wire 10 cm / 4 in. (D) from
an obstacle that is less than 1 cm / 0.4 in.
10 cm / 4"
max 1 cm / 0.4"
If you have a paving stone path that is in
level with the lawn, put the boundary wire
below the paving stone.
Note: If the paving stone is minimum 30 cm /
12 in. wide, use the factory setting for the
Drive Past Wire
function to cut all the grass
adjacent to the paving stone. Refer to
Drive
Past Wire on page 29
.
If you make an island, put the boundary wire
that runs to and from the island near
together (E). Put the wires in the same
stake. Refer to
To make an island on page
19
.
18 - Installation 1427 - 002 - 20.12.2019
Make an eyelet (F) where the guide wire is
to be connected to the boundary wire.
3.4.3.1 To put the boundary wire in a slope
The product can operate in 70% slopes. Slopes
that are too steep must be isolated with the
boundary wire. The gradient (%) is calculated as
height per m. Example: 10 cm / 100 cm = 10%.
10 cm/4"
100 cm/40"
10%
For slopes up to 50% steep inside the work
area, the product will operate normally.
Keep a distance of 1.5 m / 5 ft between the
boundary wire and obstacles, or between
obstacles.
For slopes between 50-70% steep, make
sure that there are no obstacles in the slope.
There must be a distance of 1.5 m / 5 ft from
the bottom of the slope to the boundary wire.
> 1.5 m / 5 ft
> 1.5 m / 5 ft
0% - 50%
50% - 70%
> 1.5 m / 5 ft
For slopes adjacent to a public road, put a
fence or a protective wall along the outer
edge of the slope.
3.4.3.2 Passages
A passage is a section that has boundary wire on
each side and that connects 2 work areas. The
passage must be a minimum of 2 m / 6.5 ft wide
to get a good cutting result. Short passages can
be as narrow as 60 cm / 2 ft., if a guide wire is
installed through the passage. A long narrow
passage can have a negative impact of the
cutting result.
Note: If a passage is less than 2 m / 6.5 ft. wide,
install a guide wire through the passage.
A dead end must be a minimum of 2.5 m / 8.5 ft.
wide.
>2 m / 7 ft
>2.5 m / 8.5 ft
>2 m / 7 ft
Max.
distance
>60 cm / 12"
>30 cm / 12"
Note: Make sure that the guide wire has as much
free area as possible to the left of the guide wire
when facing the charging station. Minimum
distance between the guide wire and boundary
wire is 30 cm / 12 in.
3.4.3.3 To make an island
CAUTION: Do not put a section of
boundary wire across the other. The
sections of boundary wire must be
parallel.
1427 - 002 - 20.12.2019 Installation - 19
CAUTION: Do not put the guide wire
across the boundary wire, for example
a boundary wire that goes to an island.
Some obstacles can withstand a collision, for
example, trees or bushes taller than 15 cm / 6 in.
The product will collide and then turn around with
this type of obstacle. However, obstacles that
slope slightly, for example stones or large trees
with raised roots, must be isolated or removed.
The product can run onto this kind of obstacle
causing the blades to be damaged. Use the
boundary wire to isolate areas inside the work
area by creating islands. When the boundary
wires to and from the island are put close
together, the product can run over the wire.
Note: To achieve careful and silent operation, it is
recommended to isolate all fixed objects in the
work area.
Put the boundary wire to and around the
obstacle to make an island.
Put the 2 sections of boundary wire that run
to and from the obstacle close together
without crossing.
Put the 2 sections of boundary wire in the
same stake.
Make sure that there is a minimum of 1.5 m /
5 ft of empty space before an obstacle.
0 cm/0"
1.5 m/ 5 ft 1.5 m/ 5 ft
3.4.3.4 To make a secondary area
Make a secondary area (B) if the work area has 2
areas that are not connected with a passage. The
work area with the charging station is the main
area (A).
Note: The product must be manually moved
between the main area and the secondary area.
B
A
Put the boundary wire around the secondary
area (B) to make an island. Refer to
To
make an island on page 19
.
Note: The boundary wire must be put as 1
loop around all of the work area (A + B).
Note: When the product cuts grass in the
secondary area, the
Secondary area
mode
must be selected. Refer to
Secondary area
(2nd area) on page 32
.
20 - Installation 1427 - 002 - 20.12.2019
3.4.4 To examine where to put the guide
wire
Put the guide wire from the charging station
through the work area and connect it to the
boundary wire. This product has 3 guide wires.
Use the same approach for all guide wires.
Put the guide wire in a line at a minimum of
2 m / 7 ft. in front of the charging station.
Make sure that the guide wire has as much
free area as possible to the left of the guide
wire when facing the charging station.
Put the guide wire minimum 30 cm / 12 in.
from the boundary wire.
Do not make sharp bends when you install
the guide wire.
If the work area has a slope, put the guide
wire in a straight line from the bottom of the
slope to the top of the slope. If it is not
possible to make a straight line, put the
guide wire diagonally across the slope.
CAUTION: Do not put the guide
wire in parallel with the slope, as
the illustration shows. This can
increase the wear on the grass.
3.4.5 Work area examples
If the charging station is put in a small area
(A), make sure that the distance to the
boundary wire is at a minimum 3 m / 10 ft. in
front of the charging station.
If the work area has a passage (B), make
sure that the distance to the boundary wire
is at a minimum 2 m / 6.5 ft. If the passage is
smaller than 2 m / 6.5 ft., install a guide wire
through the passage. Minimum passage
between the boundary wire is 60 cm / 24 in.
If the work area has areas which are
connected by a narrow passage (B), you
can set the product to first follow and then
leave the guide wire after a certain distance
(C). The settings can be changed in
Lawn
coverage on page 29
.
If the work area includes a secondary area
(D), refer to
To make a secondary area on
page 20
. Put the product in the secondary
area and select
Secondary area mode
.
B
D
A
C
3.5 Installation of the product
3.5.1 Installation tools
Hammer/plastic mallet: To simplify putting
the stakes into the ground.
1427 - 002 - 20.12.2019 Installation - 21
3.9 After the installation of the product
3.9.1 To do a visual check of the charging
station
1. Make sure that the indicator LED lamp on
the charging station has a green light.
2. If the indicator LED lamp does not have a
green light, do a check of the installation.
Refer to
Indicator lamp in the charging
station on page 49
and
To install the
charging station on page 22
.
3.10 Automower® Connect
The product has Automower® Connect included
from factory.
The app gives 2 modes of connectivity: Long-
range cellular connectivity and Short-range
Bluetooth® connectivity.
The product can connect to mobile devices that
have the Automower® Connect app installed.
Automower® Connect is a free app for your
mobile device. The Automower® Connect app
gives extended functions to your Husqvarna
product. You can:
See the status of your product.
Change settings to your product.
Get extended product information.
Get an alarm if the product moves out of the
work area.
See statistics of your product.
Note: All countries do not support Automower®
Connect because of regional specified cellular
systems. The included Automower® Connect
lifetime service only applies if there is a third part
sub-supplier of 2G/3G/4G available in the
operational area.
3.10.1 To install the Automower® Connect
app
1. Download the Automower® Connect app on
your mobile device.
2. Sign up for a Husqvarna account in the
Automower® Connect app.
3. Log in to your Husqvarna account in the
Automower® Connect app.
3.10.2 To pair Automower® Connect and
the product
1. Do step 1-6 in
To start the product for the
first time on page 26
.
2. Obey the instructions in the Automower®
Connect app.
3.10.3 My mowers
When you choose
My mowers
you can manage
all the products paired to your account, as well as
add new ones. If there are several paired
products it is possible to select one of them as
Current mower.
To pair a new product to the Automower®
Connect app:
1. Select the plus sign (+).
2. Select model.
3. Obey the instructions in the Automower®
Connect app to finish the pairing.
3.10.4 Firmware over the air (FOTA)
The product has a function that automatically
downloads new firmware. When a new firmware
is available, a notification shows in the app where
you can select to install the new firmware. In the
factory setting this function is enabled.
3.10.4.1 To set the Firmware over the air (FOTA)
1. Select
My Mowers
.
2. Select
Mower information
for the current
mower.
3. Select
on/off
to enable or disable the
function.
3.10.5 Automower® Direct
Automower® Direct uses short-range Bluetooth®
communication, and is included in Automower®
535 AWD.
Husqvarna cannot guarantee the time period or
coverage of the long-range cellular connectivity.
It is possible to communicate with the product
through Bluetooth® if you are in short-range of
the product. You can use Automower® Direct
without a Husqvarna account as long as you
have the product PIN code.
1427 - 002 - 20.12.2019 Installation - 25
product moves back into the work area. The
factory setting for the
Drive Past Wire function
function is 31 cm. You can select a distance of
20-50 cm.
Note: With the factory setting the product will cut
11 cm past the wire.
To set the Drive past wire
1. Select
Settings > Installation > Drive past
wire
in the app.
2. Move the horizontal bar to set the distance.
3. Select
Save
.
3.12.3.4 Starting point
The
Starting point
function allows you to control
how far the product drives forward from the
charging station before it starts to operate. Use
this function if the charging station is placed in an
area with limited space, for example under a
veranda.
Note: Starting point must not be set to a distance
longer than the distance the guide wire is
installed in a line in front of the charging station.
Refer to
To examine where to put the guide wire
on page 21
.
To set the starting point
1. Select
Settings > Installation > Starting point
in the app.
2. Move the horizontal bar to set the distance.
3. Select
Save
.
3.12.4 Accessories
In
Accessories
you can change the
settings of the product accessories. To
change the settings, obey the
instructions in the Automower®
Connect app.
3.12.4.1 To avoid collisions with the mower
house
When this option is enabled, the wear on the
product and the house is reduced, but it can
result in more uncut grass around the charging
station.
1. Select
Settings > Installation > Mower house
in the app.
2. Select
on/off
to enable or disable the
function.
3. Select
Save
.
3.12.5 General (Bluetooth® only)
This function is used to set time and
date, or to reset to default settings. To
change the settings, obey the
instructions in the Automower®
Connect app.
3.12.5.1 Time & date
The time and date can be changed manually, or
by using the time and date from the mobile
device.
To set the time & date
1. Select
Settings > General > Time & Date
in
the app.
2. Select
Time & Date from phone
or select the
pencil to enter the correct time and date.
3. Select
Save
.
3.12.5.2 Reset to factory settings
The user settings can be reset to factory settings.
Note:
PIN code, Loop signal, Messages
and
Date
& Time
will not be reset.
To reset to factory settings
1. Select
Settings > General > Reset
in the
app.
2. Select
Reset to factory settings
.
3.12.6 Security (Bluetooth® only)
The security settings controls the PIN
code, the GeoFence and other security
functions. To change the settings,
obey the instructions in the
Automower® Connect app. The correct
PIN-code must be entered to get
access to the
Security
menu in the
Automower® Connect app.
3.12.6.1 New loop signal
The loop signal is randomly selected to create a
unique link between the product and the charging
station. In rare cases, there may be a need to
generate a new signal, for instance if 2 adjacent
installations have a very similar signal.
30 - Installation 1427 - 002 - 20.12.2019
To create a New loop signal
1. Put the product in the charging station.
2. Select
Settings > Security > New loop signal
in the app.
3. Select
Create new loop signal
.
4. Select
Save
.
5. Wait for confirmation that the loop signal has
been generated. This usually takes about 10
seconds.
3.12.6.2 To change the PIN code
1. Select
Settings > Security > Change PIN
code
in the app.
2. Enter the PIN code.
3. Enter the new PIN code.
4. Enter the new PIN code to confirm.
5. Make a note of the new PIN code in Memo.
Refer to
Introduction on page 3
.
3.12.6.3 Theft protection
In the
Theft protection
menu it is possible to set
the alarm duration and also what events should
trigger the alarm. The factory setting is to require
PIN code and the alarm duration is 1 min.
Alarm duration
There is a possibility to set how long the alarm
signal should last. A setting between 1 and 10
minutes is possible.
STOP button pressed
If the alarm
"STOP button pressed"
is enabled,
the alarm goes off if someone presses the STOP
button and the PIN code is not entered within 30
seconds.
Carried away
If the alarm
Carried away
is enabled, the product
senses unexpected motions, and the alarm goes
off.
To set the Theft protection
1. Select
Settings > Security > Theft protection
in the app.
2. Select the on/off button to enable or disable
the
STOP button pressed
and
Carried away
.
3. Move the horizontal bar to select the
duration of the alarm.
3.12.6.4 GeoFence
GeoFence is a GPS-based theft protection that
makes a virtual fence for the product. If the
product is more than 500 m / 1650 ft away from
the center position the product will be deactivated
and an alarm will start. The PIN code is needed
to deactivate the alarm and to start the product
again.
To set the center position for the GeoFence
function
1. Select
Settings > Security > GeoFence
in
the app.
2. Put the product in a central position of the
work area.
3. Select the
on/off
button to enable or disable
the GeoFence function. The center position
will be set to the current position of the
product.
3.12.7 Automower® Connect (Bluetooth®
only)
In
Automower® Connect
you can
enable or disable the Automower®
Connect module. You can also see the
signal strength, connectivity status,
initiate new pairing or remove the
product from the paired accounts.
3.12.8 Messages
In this menu the previous fault and information
messages can be found. For some of the
messages, there are tips and advice to help to
rectify the fault.
If the product is disrupted in any way, for
example it is trapped or the battery is low, a
message is saved relating to the disruption and
the time it happened.
If the same message is repeated several times,
this may indicate that an adjustment to the
installation or the product is required. Refer to
Installation on page 16
.
1427 - 002 - 20.12.2019 Installation - 31
4. Make sure that the blade disc can rotate
freely.
5. Make sure that the blades are not damaged
and can pivot freely.
5.2.2 Chassis
Clean the underside of the chassis. Brush or
wipe with a damp cloth.
5.2.3 Wheels
Clean around the wheels. Grass on the wheels
can impact on how the product performs in
slopes.
5.2.4 The body of the product
Use a moist, soft sponge or cloth to clean the
body of the product. If the body of the product is
dirty, use a mild soap solution to clean it.
5.2.5 Charging station
WARNING: Use the plug to disconnect
the charging station before any
maintenance, or cleaning of charging
station or power supply.
Clean the charging station regularly from grass,
leaves, twigs and other objects that may impede
docking.
5.3 Replace the blades
WARNING: Use blades and screws of
the right type. Husqvarna can only
guarantee safety when using original
blades. Only replacing the blades and
reusing the screw can result in a screw
wearing during mowing. The blades
can then be propelled from under the
body and cause serious injury.
Replace worn or damaged parts for safety
reasons. Even if the blades are intact, they
should be replaced on a regular basis for the best
mowing result and low energy usage. All 3 blades
and screws must be replaced at the same time to
obtain a balanced cutting system. Use
Husqvarna original blades embossed with the
crowned H-mark logotype, refer to
Warranty
terms on page 59
.
5.3.1 To replace the blades
1. Switch off the product. Refer to
To switch off
the product on page 33
.
2. Put on protective gloves.
3. Turn the product upside down. Place the
product on a soft and clean surface to avoid
scratching the body.
4. Rotate the skid plate so that its holes align
with the screws for the blade.
36 - Maintenance 1427 - 002 - 20.12.2019
6 Troubleshooting
6.1 Introduction - troubleshooting
In this chapter, a number of messages are listed which may be shown in Automower® Connect if there
is a malfunction. There is a proposal as to the cause and steps to take for each message. This chapter
also presents some symptoms that can guide you if the product does not work as expected. More
suggestions for steps to take in the event of malfunction or symptoms can be found on
www.husqvarna.com.
6.2 Fault messages
The table below shows a number of fault messages that may be shown in Automower® Connect. Some
of the errors can be confirmed in the Automower® Connect and some the message needs to be
1427 - 002 - 20.12.2019 Troubleshooting - 41
confirmed on the product. Contact your local Husqvarna representative if the same message appears
often. For more information, refer to
Messages on page 31
.
Message Cause Action
No loop signal
The power supply or the voltage cable
are not connected.
Examine the LED status on the charg-
ing station. If the LED is not lit, it indi-
cates that there is no power. Examine
the wall socket connection and whether
an earth-fault breaker has tripped.
Make sure that the low voltage cable is
connected to the charging station.
The power supply or low voltage cable
are damaged.
Replace the power supply or low volt-
age cable.
The boundary wire is not connected to
the charging station.
Make sure that the boundary wire con-
nectors are fitted properly to the charg-
ing station. Replace connectors if dam-
aged. Refer to
To install the charging
station on page 22
.
The boundary wire is broken. Check the signal given by the LED on
the charging station. If the LED indi-
cates break in the boundary wire, find
out where the break is. Replace the
damaged section of the loop with a new
loop wire and splice using an original
coupler. Refer to
Find breaks in the
loop wire on page 51
.
ECO mode
is activated and the prod-
uct has attempted to start outside the
charging station.
Put the product in the charging station.
Start the product and close the hatch.
The pairing between the product and
the charging station is lost.
Put the product in the charging station
and generate a new loop signal. Refer
to
To create a New loop signal on page
31
.
The boundary wire is crossed on its
way to and from an island.
Make sure that the boundary wire is in-
stalled correctly. Refer to
To install the
boundary wire on page 23
.
Disturbances from metal objects (fen-
ces, reinforcement steel) or buried ca-
bles.
Move the boundary wire and/or make
more islands in the work area to in-
crease the signal strength.
Wheel motor
blocked
Grass or other object has wrapped
around the drive wheel.
Examine the drive wheel and remove
the grass or other object.
Wheel drive prob-
lem
42 - Troubleshooting 1427 - 002 - 20.12.2019
Message Cause Action
Cutting system
blocked
Grass or other object has wrapped
around the blade disc.
Examine the blade disc and remove the
grass or other object.
The blade disc lies in a pool of water. Move the product and prevent the col-
lection of water in the work area.
Message Cause Action
Trapped
The product is stuck in a small area be-
hind a number of obstacles.
Examine if there are any obstacles
which make it hard for the product to
move away from this location.
Wrong PIN code
Wrong PIN code has been entered.
Five attempts are permitted, and the
product is then blocked for a period of
time.
Enter the correct PIN code. If the PIN
code is incorrect, use the link in the app
to send the PIN code to your registered
e-mail address. If you have not regis-
tered the e-mail address, contact your
local Husqvarna representative.
Empty battery
The product cannot find the charging
station.
Change the position of the guide wire.
Refer to
To install the guide wire on
page 23
.
Check the installation settings about
how to find the charging station. Refer
to
To find the charging station on page
28
.
The battery is spent. Replace the battery. Refer to
Battery
on page 39
.
The charging station’s antenna is de-
fective.
Check if the indicator lamp in the
charging station flashes red. Refer to
Indicator lamp in the charging station
on page 49
.
No drive
The product is caught in something and
has been slipping.
Free the product and rectify the reason
for the lack of drive. If it is due to wet
grass, wait until the lawn has dried be-
fore using the product.
The work area includes a steep slope. Maximum guaranteed slope is 70%.
Steeper slopes should be isolated. Re-
fer to
To put the boundary wire in a
slope on page 19
.
The guide wire is not installed correctly
in a slope.
Make sure that the guide wire is instal-
led diagonally across the slope. Refer
to
To install the guide wire on page 23
.
Wheel motor over-
loaded
The product is caught in something. Free the product and rectify the reason
for the lack of drive. If it is due to wet
grass, wait until the lawn has dried be-
fore using the product.
1427 - 002 - 20.12.2019 Troubleshooting - 43
Message Cause Action
Charging station
blocked
The contact between the charging
strips and contact strips may be poor
and the product has made a number of
attempts to charge.
Put the product in the charging station
and check that the charging strips and
contact strips make good contact.
Clean the contact and charging plates.
An object causes a blockage and the
product cannot enter the charging sta-
tion.
Remove the object.
The baseplate is tilted or bent. Make sure that the baseplate is put on
level ground.
Stuck in charging
station
The product slips on the baseplate. Clean the baseplate.
There is an object in the way of the
product preventing it from leaving the
charging station.
Remove the object.
Upside down
The product is leaning too much or has
turned over.
Turn the product the right way up.
Mower tilted
The product is tilted more than the
maximum angle.
Move the product to a flat area.
Lifted
A blockage has activated the lift senors
and caused the product to stop.
Remove the product from the blockage.
If the problem remains it requires action
by authorized service technician.
Collision sensor
problem
The product body can not move freely
around its chassis.
Make sure that the product body can
move freely around its chassis.
If the problem remains, the message
requires action by authorized service
technician.
Slope too steep
Mower stopped because the slope is
too steep.
Change the installation of the boundary
wire to exclude this steep part of the
work area. Refer to
To examine where
to put the boundary wire on page 17
.
Alarm! Mower
switched off
The alarm was activated because the
product was switched OFF.
Adjust the security level in the
Security
menu, refer to
Security (Bluetooth® on-
ly) on page 30
.
Alarm! Mower
stopped
The alarm was activated because the
product was stopped.
Alarm! Mower was
moved
The alarm was activated because the
product was moved.
Alarm! Outside ge-
ofence
The alarm was activated because the
mower was outside its GeoFence.
Adjust the theft protection area (Geo-
Fence) in the
Automower Connect
menu.
44 - Troubleshooting 1427 - 002 - 20.12.2019
Mowing Automower® 535 AWD AWD
Cutting system 3 pivoted cutting blades
Maximum blade motor speed, rpm 2475
Power consumption during cutting, W +/- 20 % 40
Cutting height, cm / in. 3-7 / 1.2-2.8
Cutting width, cm / in. 22 / 8.7
Narrowest possible passage, cm / in. 60 / 24
Maximum angle for work area, % 70
Maximum angle for boundary wire, % 50
Maximum length boundary wire, m / ft 800 / 2600
Maximum length guide loop, m / ft 400 / 1300
Working capacity, m2 / yd2, +/- 20% 3500
IP-classification Automower® 535 AWD AWD
Robotic lawnmower IPX4
Charging station IPX1
Power supply IPX4
Frequency Band Support
Bluetooth® Frequency range 2400.0-2483.5 MHz
Automower® Connect 2G GSM 850 MHz
E-GSM 900 MHz
DCS 1800 MHz
PCS 1900 MHz
Automower® Connect 3G Band 19 (800 MHz)
Band 5 (850 MHz)
Band 8 (900 MHz)
Band 2 (1900 MHz)
Band 1 (2100 MHz)
1427 - 002 - 20.12.2019 Technical data - 57
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Automower 535 AWD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Automower 535 AWD in the language / languages: English as an attachment in your email.

The manual is 5,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Automower 535 AWD

Husqvarna Automower 535 AWD User Manual - German - 68 pages

Husqvarna Automower 535 AWD User Manual - Dutch - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info