819078
25
Zoom out
Zoom in
Previous page
1/52
Next page
alarm. The factory setting is to require PIN code and the
alarm duration is 1 min.
4.7.3.1 Require PIN code
This function means that the product cannot be operated
or controlled after the STOP button has been pushed
without first entering the correct PIN code. If the
incorrect PIN code is entered 5 times, the product is
locked for a time. The lock is extended for each new
incorrect try.
4.7.3.2 Alarm duration
There is a possibility to set how long the alarm signal
should last. A setting between 1 and 10 minutes is
possible.
4.7.3.3 STOP button pressed
If the alarm
"STOP button pressed"
is enabled, the
alarm goes off if someone presses the STOP button and
the PIN code is not entered within 30 seconds.
4.7.3.4 Carried away
If the alarm
Carried away
is enabled, the product senses
unexpected motions, and the alarm goes off.
4.7.4 GeoFence
GeoFence is a GPS-based theft protection that makes
a virtual fence for the product. If the product is more
than a set distance away from the center position the
product will be disabled and an alarm will start. The
center position sets to the current position of the product
when GeoFence is enabled. The PIN code is necessary
to stop the alarm and to start the product again. The
GeoFence is only enabled when the product is set to
ON.
4.8 Automower® Connect
In
Automower® Connect
you can enable or disable the
Automower® Connect function. You can connect the
product to a Wi-Fi network. You can also see the signal
strength and connectivity status.
This menu is only available when your mobile device is
connected to the product with Bluetooth®.
4.9 Messages
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
If the product is disrupted in any way, for example it
is trapped or the battery is low, a message is saved
relating to the disruption and the time it happened.
If the same message is repeated several times, this
may indicate that an adjustment to the installation or the
product is required. Refer to
Installation on page 12
.
4.10 Automower® Intelligent Mapping
(AIM)
Automower® Intelligent Mapping (AIM) is available in
the Automower® Connect app. The technology uses
different sensors, GPS included, in the product. The
precision of the map is approximately 1 m / 3.3 ft.
B
A
C
Some of the functions with AIM are:
It shows a map of the lawn in Automower®
Connect app with charging station, boundary wire,
guide wire and islands.
You can make work areas (A) and (B) in the
installation where you can set a schedule and
cutting height for each work area.
You can make stay-out zones (C) in which the
product cannot enter and cut grass.
Note: With the AIM function you can set work areas
and stay-out zones with a precision of approximately 1
m / 3.3 ft.
The data collection for the AIM map starts automatically.
The product collects data while it operates and the
map is completed in 1-2 weeks. Remove temporary
obstacles on the lawn when the product operates and
collects data. If you change the installation of the wires
or charging station, you must do a new map. Read more
about AIM in the Automower® Connect app.
4.11 Download firmware over the air
FOTA (Firmware over the air)
The product has a function that automatically downloads
new firmware. When a new firmware is available, a
notification shows in the app where you can select
to install the new firmware. The LED indicator of the
product pulsates when the firmware update is ongoing.
If the product does not use cellular connectivity, it
2071 - 002 - 05.02.2024 Settings - 25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Automower 450X NERA - 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Automower 450X NERA - 2024 in the language / languages: English as an attachment in your email.

The manual is 4.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Automower 450X NERA - 2024

Husqvarna Automower 450X NERA - 2024 Quick start guide - English, German - 8 pages

Husqvarna Automower 450X NERA - 2024 User Manual - German - 52 pages

Husqvarna Automower 450X NERA - 2024 User Manual - Dutch - 52 pages

Husqvarna Automower 450X NERA - 2024 Quick start guide - French, Italian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info