819071
33
Zoom out
Zoom in
Previous page
1/48
Next page
Message Cause Action
Lifted
The lift sensor has been enabled because
the product has been lifted.
Make sure that the body of the product body
can move freely around its chassis. Remove
or make an island around objects that can
cause the body to be lifted. If the problem
stays, speak to your authorized service cen-
ter.
Trapped
The product is blocked in a small area be-
hind a number of obstacles.
Examine if there are obstacles which make it
hard for the product to move away from this
location.
Slipped
The product slips because there is an obsta-
cle.
Remove the obstacle.
The product slips because of wet grass. Wait until the lawn is dry before you start the
product again.
The product has hit an obstacle and stopped
or the wheels cannot move on the wet grass.
Free the product and rectify the reason for
the lack of drive. If it is due to wet grass,
wait until the lawn has dried before using the
product.
The product slips because the slope is too
steep.
Isolate the steep slope with boundary wire.
Refer to
To put the boundary wire in a slope
on page 14
.
The product slips because the slope is too
steep when it follows the guide wire.
Make sure that the guide wire is installed
diagonally in the slope. Refer to
To put the
boundary wire in a slope on page 14
.
Collision
The body of the product cannot move freely
around its chassis.
Make sure that the body of the product can
move freely around its chassis. Examine that
the body of the product is correctly installed
and there is no dirt blocking it. If the problem
stays, speak to your authorized service cen-
ter.
Alarm! Mower stop-
ped
The alarm was started because the product
was stopped.
Enter the PIN code to disable the alarm. The
settings for the alarm can be changed in the
Security
menu. Refer to
Security on page 23
.
The alarm was started because the product
was lifted.
The alarm was started because the product
was tilted.
Alarm! Mower was
moved
The alarm was started because the product
was moved.
Alarm! Outside Geo-
Fence
The alarm was started because the product
was outside the GeoFence.
Temporary problem
Temporary electronic or firmware problem in
the product.
Update the firmware via FOTA. Restart the
product. If the problem stays, speak to your
authorized service center.
2369 - 001 - 05.02.2024 Troubleshooting - 33
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Automower 410XE NERA - 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Automower 410XE NERA - 2024 in the language / languages: English as an attachment in your email.

The manual is 4.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Automower 410XE NERA - 2024

Husqvarna Automower 410XE NERA - 2024 User Manual - German - 48 pages

Husqvarna Automower 410XE NERA - 2024 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info