819076
6
Zoom out
Zoom in
Previous page
1/8
Next page
This Quick Guide gives you information about how to install
your robotic lawn mower with a wire installation. If you install
your product with EPOS™ technology without boundary wire,
read the Operator's manual supplied with the Reference
station EPOS™ RS1.
To start the product for the first time
1.
Download the Automower® Connect app from App Store or
Google Play.
2. Sign up and specify an e-mail address and a password to
create a Husqvarna account.
3. Log in to your Husqvarna account in the app.
4. Push the jog wheel for 3 seconds to switch on the robotic
lawn mower.
5. Enter the factory PIN code 1234 on the robotic lawn mower.
6. Select My mowers in the Automower® Connect app, and
then select the plus sign (+).
7. Follow the instructions in the app.
A Placement of and connecting the
charging station
1.
Place the charging station at a central position in the work
area, with a lot of open space in front of the charging
station and on a relatively horizontal surface.
2. Attach the top of the charging station.
3. Put the grommet with the cables into position.
4. Connect the cable to the charging station.
5.
Connect the power supply’s low-voltage cable to the
charging station and the power supply.
6.
Connect the power supply to a 100-240 V wall socket.
7.
Place the robotic lawn mower in the charging station to
charge the battery while the boundary wire is laid.
B
Placement of the boundary wire and the
guide wire
1.
Lay the boundary wire so that it forms a loop around the
working area.
2.
Make an eyelet at the point where the guide wire will later
be connected.
3.
Run the guide wire to the point on the boundary loop where
the connection will be made. Avoid laying the wire at tight
angles.
C
Connecting the boundary wire and the guide
wire
1.
Narrow passages in the yard make it difficult for the robotic
lawn mower to find the charging station. The robotic lawn
mower can be lead to remote areas using the guide wire.
The guide wire also helps the robotic lawn mower to
quickly find the charging station.
2.
Lay the guide wire under the charging station and at least
2 m / 7 ft straight out from the front edge of the charging
station.
3.
Open the connectors and lay the wire ends in the recesses
on each connector.
4.
Press the connectors together using a pair of pliers.
5.
Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8”
above the connectors.
6.
Press the connectors onto the contact pins, marked AL
(left) and AR (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand
contact pin, and the left-hand wire to the left-hand pin.
7.
Fasten the connector to the contact pin marked G1/G2/G3
on the charging station.
D
Connecting the guide wire to the boundary
wire
1.
Cut the boundary wire with a wire cutters at the centre of
the eyelet that was made in step B.2.
2.
Connect the guide wire to the boundary wire using the
accompanying couplers. Press the couplers completely
together with a polygrip.
Maintenance
Set the product to OFF before all work on the robotic lawn
mower’s chassis, such as cleaning or replacing the
blades. Replace the blades regularly for the best mowing
result
.
Never use a high-pressure washer to clean the robotic
lawn mower. Never use solvents for cleaning. Clean the
product with a brush and a water hose.
All connections to the charging station (power supply,
boundary and guide wire) must be disconnected if there
is a risk of a thunderstorm
.
Fully charge the battery at the end of the season before
winter storage.
QUICK GUIDE en
For more information and instructions,
read the complete Operator’s manual in the
Automower
®
Connect app or on
www.husqvarna.com.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Automower 320 NERA - 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Automower 320 NERA - 2024 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 6.46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Automower 320 NERA - 2024

Husqvarna Automower 320 NERA - 2024 User Manual - English - 52 pages

Husqvarna Automower 320 NERA - 2024 User Manual - German - 52 pages

Husqvarna Automower 320 NERA - 2024 User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info