819076
34
Zoom out
Zoom in
Previous page
1/52
Next page
Message Cause Action
No loop signal
There is no power in the charging station.
The LED indicator on the charging station is
not on.
Examine if the power supply unit or the low-
voltage cable is damaged or not installed
correctly to the power outlet or the charging
station. Examine if there is a power failure or
if a residual-current device is enabled.
The boundary wire is damaged or not instal-
led correctly.
Make sure that the boundary wire is connec-
ted correctly to the charging station. Examine
all splices on the boundary wire. Examine if
there is a break in the boundary wire and
repair if necessary. Refer to
To install the
boundary wire on page 18
.
ECO mode
is enabled and the loop signal is
disabled when the product is started in the
work area.
Put the product in the charging station and
start the product. To start the product man-
ually in the work area, push the STOP but-
ton before you remove the product from the
charging station.
The boundary wire is crossed on its way to
and from an island.
Make sure that the boundary wire is put
down correctly. Refer to
To install the charg-
ing station on page 17
.
The product does not find the loop signal
from the charging station.
Put the product in the charging station and
generate a new loop signal. Refer to
New
loop signal on page 24
.
Disturbances from metal objects (fences, re-
inforcement steel) or buried cables close by.
Try to move the boundary wire and/or make
more islands in the work area to increase the
signal strength.
The product is too far from the boundary
wire.
Redo the installation of the boundary wire so
that all parts of the work area is maximum 35
m / 115 ft. from the boundary wire.
Outside work area
The boundary wire connections to the charg-
ing station are crossed.
Make sure that the boundary wire is connec-
ted correctly to the charging station. Refer to
To install the boundary wire on page 18
.
The boundary wire is too close to the edge of
the work area.
Make sure that the boundary wire is put
down correctly. Refer to
To install the boun-
dary wire on page 18
.
The work area is too steep by the boundary
wire.
The boundary wire around an island is not
installed correctly. The boundary wires are
crossed.
Disturbances from metal objects (fences, re-
inforcement steel) or buried cables close by.
Try to move the boundary wire and/or make
more islands in the work area to increase the
signal strength.
The product cannot find the correct loop sig-
nal because of interference with a loop signal
from a different product installation nearby.
Put the product in the charging station and
generate a new loop signal. Refer to
New
loop signal on page 24
.
Upside down
The product is leaning too much or has
turned over.
Turn the product the right way up.
Mower tilted
The product tilts too much. Move the product to a level area.
34 - Troubleshooting 2071 - 002 - 05.02.2024
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna Automower 320 NERA - 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna Automower 320 NERA - 2024 in the language / languages: English as an attachment in your email.

The manual is 4.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna Automower 320 NERA - 2024

Husqvarna Automower 320 NERA - 2024 Quick start guide - English, German - 8 pages

Husqvarna Automower 320 NERA - 2024 User Manual - German - 52 pages

Husqvarna Automower 320 NERA - 2024 User Manual - Dutch - 52 pages

Husqvarna Automower 320 NERA - 2024 Quick start guide - French, Italian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info