734098
21
Zoom out
Zoom in
Previous page
1/32
Next page
Maintenance Daily Weekly Monthly
Clean the air filter. Replace if it is necessary. X
Make sure that the blade is sharp and put correctly in the center, look for cracks.
If the blade is not in the center correctly, it can cause damage to the product. X
Examine the cutting attachment guard for damages and cracks. Replace it if it is
damaged. X
Examine the trimmer head for damages and cracks. Replace it if it is damaged. X
Make sure that the screws and nuts are tight. X
Examine the engine, the fuel tank and the fuel lines for leaks. X
Examine the transport guard. Make sure that the blade is not damaged and that
the transport guard can be attached correctly. X
Clean the cooling system. X
Examine the starter and the starter rope for damages. X
Examine the vibration damping units for damages and cracks. X
Clean the external surface part of the spark plug. Remove it and do a check of
the electrode gap. Adjust the electrode gap to the correct distance (refer to
Technical data on page 25
) or replace the spark plug. Make sure that the spark
plug has a supressor.
X
Clean the external surface of the carburetor and the area around it. X
Do a check of the bevel gear to make sure that it is filled ¾ with lubricant. Use
special grease to fill if it is necessary. X
Clean or replace the spark arrestor mesh on the muffler. X
Do a check of the fuel filter for contamination and the fuel hose for cracks or oth-
er defects. Replace if it is necessary. X
Do a check of all cables and connections. X
Do a check of the clutch, clutch springs and the clutch drum for wear. If it is nec-
essary to replace 1 or more of these units, speak to your servicing dealer. X
Replace the spark plug. Make sure that the spark plug has a supressor. X
Examine and clean the spark arrestor mesh on the muffler. X
To adjust the idle speed
WARNING: Read the warning instructions in
the safety chapter before you start the
product. Refer to
Safety on page 4
).
WARNING: If the cutting attachment rotates
when the engine is at idle speed the idle
adjustment screw T must be turned
counterclockwise until the cutting
attachment stops.
1. Make sure that the air filter is clean.
2. Make sure that the air filter cover is in position.
3. Get the idle adjustment screw T.
4. Turn the idle adjustment screw T clockwise until the
cutting attachment starts to rotate
T
.
1104 - 005 - 21
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 553RBX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 553RBX in the language / languages: English as an attachment in your email.

The manual is 2,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 553RBX

Husqvarna 553RBX User Manual - English, German, French, Italian, Polish, Portuguese, Turkish, Spanish - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info