734098

Husqvarna 553RBX Manual

7
Zoom out
Zoom in
Previous page
1/32
Next page
• Avoid all usage which you consider to be beyond
your capability.
• Do not use the product unless you are able to call for
help in the event of an accident.
• Using an incorrect cutting attachment or an
incorrectly sharpened blade increases the risk of
blade thrust.
• Products fitted with saw blades or grass blades can
be thrown violently to the side when the blade comes
into contact with a fixed object. This is called blade
thrust. A blade thrust can be violent enough to cause
the product and/or operator to be propelled in any
direction, and possibly lose control of the product.
Blade thrust can occur without warning if the product
snags, stalls or binds. Blade thrust is more likely to
occur in areas where it is difficult to see the material
being cut.
• Avoid cutting with the area of the blade between the
12 o'clock and 3 o'clock positions. Because of the
speed of rotation of the blade, blade thrust can occur
if you attempt to cut thick stems with this area of the
blade.
• Mufflers fitted with catalytic converters get very hot
during use and remain so for some time after
stopping. This also applies at idle speed. Contact
can result in burns to the skin. Remember the risk of
fire.
• Only use cutting attachments with the guards we
recommend. Refer to
Accessories on page 26
.
To do a check of the throttle trigger lockout
The throttle trigger lockout locks the throttle trigger at the
idle position to prevent accidental operation of the
throttle trigger. When you release the handle of the
throttle trigger and the throttle trigger lockout the two
move back to their initial positions.
1. Push the throttle trigger lockout (A). Make sure that
the throttle trigger (B) is released.
A
B
2. Make sure that the throttle trigger (B) is locked at the
idle position when the throttle trigger lockout is
released.
3. Push the throttle trigger lockout (A) and make sure
that it goes back to its initial position when you
release it.
4. Make sure that the throttle trigger lockout (A) and the
throttle trigger (B) move freely.
5. Start the product and apply full throttle. Refer to
To
start the engine on page 17
6. Release the throttle trigger (B) and make sure that
the cutting attachment stops and stays stationary.
WARNING: If the cutting attachment moves
when the throttle trigger is in the idle
position, adjust the idle speed. Refer to
To
adjust the idle speed on page 21
.
To do a check of the stop switch
1. Start the engine.
2. Move the stop switch to the stop position and make
sure that the engine stops.
To do a check of the cutting attachment guard
WARNING: An incorrect or defective cutting
attachment guard can cause serious injury.
Refer to
Accessories on page 26
.
WARNING: Always use the recommended
cutting attachment guard for the cutting
attachment that you use. If an incorrect or
defective cutting attachment guard is
installed, this can cause serious injury. Refer
to
Accessories on page 26
.
1104 - 005 - 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 553RBX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 553RBX in the language / languages: English as an attachment in your email.

The manual is 2,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 553RBX

Husqvarna 553RBX User Manual - English, German, French, Italian, Polish, Portuguese, Turkish, Spanish - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info