733980
19
Zoom out
Zoom in
Previous page
1/32
Next page
2. Adjust the harness for the best work position. An
adjusted harness and product makes operation
easier.
Before you operate the product
Examine the work area to make sure that you know
the type of terrain, the slope of the ground and if
there are obstacles such as stones, branches and
ditches.
Do an overhaul inspection of the product.
Do the safety inspections, maintenance and
servicing that are given in this manual.
Make sure that all covers, guards, handles and the
cutting equipment are correctly attached and not
damaged.
Make sure that there are no cracks at the bottom of
the saw blade or grass blade teeth or by the center
hole of the blade. Replace the blade if it is damaged.
Examine the support flange for cracks. Replace the
support flange if it is damaged.
Make sure that the locknut can not be removed by
hand. The locknut must have a locking force of
minimum 1.5Nm. Make sure that the tightening
torque is between 35-50 Nm.
Examine the blade guard for damages or cracks.
Replace the blade guard if it has been hit or if it has
cracks.
Examine the trimmer head and cutting attachment
guard for damages or cracks. Replace the trimmer
head and cutting attachment guard if they have been
hit or if they have cracks.
To start the product
Note: The product identifies the cutting attachment when
the cutting attachment is changed and the power trigger
is pressed. The product stops and the LED flashes until
the power trigger is released and moves back to its
initial position. The cutting attachment is at this time
identified and prepared for operation.
1. Push and hold the start button until the green battery
LED and the white mode LED comes on.
2. Use the power trigger to control the speed.
To limit the maximum speed with the
mode button
Note: The maximum speed is related to the cutting
equipment that is attached and identified by the product.
When a blade is attached, the maximum speed is higher
than when a trimmer head is attached. Refer to
Technical data on page 27
.
The product has a mode button. With the mode button
the operator can limit the maximum speed. The mode
button has 3 speed levels. A lower level increases the
time of operation for the product. Use level 1 and level 2
if the operation does not require full speed/full power. If
the operation condition requires full speed/full power,
use level 3.Do not use a higher level than necessary for
the operation.
609 - 006 - 17.08.2020 19
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 535iRX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 535iRX in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 535iRX

Husqvarna 535iRX User Manual - German, Dutch, French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info