733981
10
Zoom out
Zoom in
Previous page
1/32
Next page
careful around the sharp edges of the
cutting attachment.
A locknut is used to attach some types of cutting
attachments. The locknut has a left thread.
To attach, tighten the locknut in the opposite
direction to the direction of rotation of the cutting
attachment.
To remove the locknut, undo the lock nut in the
same direction as the cutting attachment rotates.
To loose and tighten the locknut, use a socket
spanner with a long shaft. The arrow in the picture
shows the area where you should operate the socket
spanner.
WARNING: When you loose and tighten
the locknut there is a risk of injury from
the teeth of the saw blade. You should
therefore always ensure that your hand
is shielded by the blade guard when you
do this.
Note: Make sure that you can not turn the locknut by
hand. Replace the nut if the nylon lining does not have a
resistance of a minimum of 1.5 Nm. The nut should be
replaced after it has been put on approximately 10
times.
Cutting attachment
WARNING: Remove the battery and make
sure that the cutting attachment stops
completely before you work on any part of
the cutting attachment.
WARNING: Use correct cutting attachment.
Only use the cutting attachment with the
guards we recommend, refer to
Accessories
on page 28
. Make sure that the cutting
attachment is sharpened correctly. A cutting
attachment that is not sharpened correctly
increases the risk of blade thrust.
WARNING: An incorrectly sharpened or
damaged blade increases the risk of
accidents. Keep the teeth of the blade
correctly sharpened. Follow the instructions
and use the recommended file gauge.
WARNING: A coasting blade can cause
injury while it continues to spin after the
switch has been released. Need to maintain
proper control until the blade has completely
stopped rotating.
CAUTION: An incorrectly set saw blade
increases the risk of jamming and blade
thrust. This can damage the saw blade.
Keep the correct setting on the saw blade.
Follow the instructions and use the
recommended setting tool.
Wear protective gloves when the cutting attachment is
handled.
Use the saw blade to cut fibrous types of wood.
Use the blades and grass knives to cut coarse grass.
Use the trimmer head to trim grass.
Check the cutting attachment for damage or cracks.
Replace a damaged cutting attachment.
Trimmer head
Always use the correct trimmer head, cutting
attachments and always use the recommended
trimmer line. Refer to
Accessories on page 28
and
the assembly in the end of the Manual.
Make sure that the cutter on the trimmer guard is not
damaged.
Make sure that the trimmer line is wound tightly and
equally around the drum to prevent unusual
vibrations from the product. Different cord lengths
can result in vibrations that are not necessary. Tap
the trimmer head to get correct length on the cord.
To increase the life of the cord it can be soaked in water
for 2 days or more before assembly. This will make the
cord more resistant.
Saw blade and grass blade
Use correctly sharpened blades. An incorrectly
sharpened or damaged blade increases the risk of
injury.
10 609 - 006 - 17.08.2020
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 535iFR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 535iFR in the language / languages: English as an attachment in your email.

The manual is 3,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 535iFR

Husqvarna 535iFR User Manual - German, Dutch, French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info