734091
14
Zoom out
Zoom in
Previous page
1/36
Next page
ASSEMBLY
14 – English
Fitting the blade guard and saw
blade
Remove the mounting plate (H). Fit the adapter (I) and
bracket (J) with the two screws (K) as shown. Fit the
blade guard (A) to the adapter using the 4 screws (L)
as shown.
CAUTION! Use the recommended blade guard. See
the Technical data section.
Fit the drive disc (B) on the output shaft.
Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
Insert the locking pin (C) in the hole to lock the shaft.
Place the blade (D) and support flange (F) on the
output shaft.
Fit the nut (G). The nut must be tightened to a torque
of 35-50 Nm (3.5-5 kpm). Use the spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
guard as possible. To tighten the nut, turn the spanner
in the opposite direction to the direction of rotation
(Caution! left-hand thread).
When loosening and tightening the saw blade nut,
there is a risk of injury from the teeth of the saw blade.
You should therefore always ensure that your hand is
shielded by the blade guard when doing this. Always
use a socket spanner with a shaft that is long enough
to allow this. The arrow in the diagram shows the area
where you should operate the socket spanner when
loosening or tightening the nut.
Fitting other guards and cutting
attachments
Fit the trimmer guard/combination guard (A) intended
for use with the trimmer head/plastic blades. Hook the
guard onto the fitting on the shaft and secure it with
the bolt (L).
Fit the drive disc (B) on the output shaft.
Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
Insert the locking pin (C) in the hole to lock the shaft.
A
L
I
J
K
H
F
D
B
C
G
L
A
H
C
B
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 525RX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 525RX in the language / languages: English as an attachment in your email.

The manual is 4,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 525RX

Husqvarna 525RX User Manual - German, Dutch, French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info