579291
9
Zoom out
Zoom in
Previous page
1/28
Next page
To do a check of the muffler
The muffler keeps noise levels to a minimum and sends
exhaust fumes away from the operator.
Do a visual check for damage and deformation.
Make sure that the muffler is correctly attached to
the product.
If the muffler on your product has a spark arrester
screen, do a visual check. Replace the spark
arrester screen if it is damaged.
a) Clean the spark arrester screen if it is blocked. A
blocked spark arrester screen causes the engine
to become too hot which causes damage to the
engine.
b) Make sure that the spark arrestor mesh is
attached correctly.
To attach and remove the locknut
WARNING:
Stop the engine, use protective
gloves and be careful around the sharp
edges of the cutting attachment.
A locknut is used to attach some types of cutting
attachments. The locknut has a left thread.
To attach, tighten the locknut in the opposite
direction to the direction of turning of the cutting
attachment.
To remove the locknut, loosen the locknut in the
same direction as the cutting attachment rotates.
To loosen and tighten the locknut, use a socket
wrench with a long shaft. The arrow in the picture
shows the area where you can operate the socket
wrench.
WARNING: When you loosen and
tighten the locknut, there is a risk of
injury from the blade. You must always
make sure that the blade guard prevents
injury to your hand when you do this.
Note: Make sure that you cannot turn the locknut by
hand. Replace the nut if the nylon lining does not have a
resistance of a minimum of 1.5 Nm. The locknut must be
replaced after it has been put on approximately 10
times.
Cutting equipment
Select correct cutting equipment and do maintenance on
the cutting equipment to:
Get maximum cutting performance.
Increase lifetime of the cutting equipment.
WARNING:
Only use cutting attachments
with the guards we recommend! See
Accessories on page 21
. Refer to the
instructions for the cutting attachment to find
the correct way to load the trimmer line and
the correct trimmer line diameter.
WARNING: A defective cutting attachment
may increase the risk of accidents.
WARNING: Always stop the engine before
you do the work on the cutting attachment.
This continues to rotate after you release the
throttle. Make sure that the cutting
attachment has stopped fully and disconnect
1309 - 002 - 27.08.2020 9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 524LK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 524LK in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 524LK

Husqvarna 524LK User Manual - German, Dutch, French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info