733974
21
Zoom out
Zoom in
Previous page
1/36
Next page
2. Attach the blade guard (A) onto the shaft, refer to
To
assemble the trimmer guard on page 20
.
A
B
D
E
F
G
C
3. Install the drive disc (B) on the output shaft.
4. Turn the output shaft until one of the holes in the
drive disc aligns with the related hole in the gear
housing.
5. Tighten the locking bolt (C) with the hex key to lock
the shaft.
6. Put the blade (D) and support cup (E) on the output
shaft.
7. Put the cup washer (F) on the output shaft.
8. Install the nut (G). Hold the shaft of the wrench near
the blade guard as much as possible. To tighten the
nut, you must turn the wrench counterclockwise
which is the opposite direction of rotation. Tighten
the nut to a torque of 35-50 Nm (3.5-5 kpm).
To attach and remove the locknut
WARNING:
Stop the engine, use protective
gloves and be careful around the sharp
edges of the cutting attachment.
A locknut is used to attach some types of cutting
attachments. The locknut has a left thread.
To attach, tighten the lock nut in the opposite
direction to the direction of rotation of the cutting
attachment.
To remove the locking nut, undo the lock nut in the
same direction as the cutting attachment rotates.
To loose and tighten the locknut, use a socket
spanner with a long shaft. The arrow in the picture
shows the area where you should operate the socket
spanner.
WARNING: When you loose and tighten
the locknut there is a risk of injury from
the teeth of the saw blade. You should
therefore always ensure that your hand
is shielded by the blade guard when you
do this.
Note: Make sure that you can not turn the locknut by
hand. Replace the nut if the nylon lining does not have a
resistance of a minimum of 1.5 Nm. The nut should be
replaced after it has been put on approximately 10
times.
To adjust the harness
WARNING:
The product must always be
correctly attached to the harness. Do not
use a defective harness.
1. Put on the harness.
757 - 003 - 24.06.2020
21
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 520iRX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 520iRX in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 520iRX

Husqvarna 520iRX User Manual - German, Dutch, French - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info