40844
32
Zoom out
Zoom in
Previous page
1/44
Next page
MAINTENANCE
32 – English
High speed jet H
At the factory the engine is adjusted at sea level.
When working at a high altitude or in different
weather conditions, temperatures and atmospheric
humidity, it may be necessary to make minor
adjustments to the high speed jet.
CAUTION! If the high speed jet is screwed in too far,
it may damage the piston/cylinder.
When test run at the factory, the high speed jet is set so
that the engine satisfies the applicable legal requirements
at the same time as achieving maximum performance.
The carburettor’s high speed jet is then locked using a
limiter cap in the fully screwed out position. The limiter cap
limits the potential to adjust the high speed jet to at most
half a turn.
To adjust the carburettor correctly you should contact a
mechanic with access to a rev counter.
CAUTION! As the spark is cut off, the rev counter does not
show speeds higher than 13600 rpm.
Correctly adjusted carburettor
When the carburettor is correctly adjusted the machine
accelerates without hesitation and 4-cycles a little at full
throttle. It is also important that the chain does not rotate
at idle. If the L-jet is set too lean it may cause starting
difficulties and poor acceleration. If the H-jet is set too
lean the machine will have less power, poor acceleration
and could suffer damage to the engine.
Checking, maintaining and servicing
chain saw safety equipment
Chain brake and front hand guard
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain
brake and clutch drum. Dirt and wear can impair operation
of the brake.
Regularly check that the brake band is at least 0.6 mm
thick at its thinnest point.
Checking the front hand guard
Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to the
clutch cover.
Checking the inertia brake release
Place the chain saw, with the engine switched off, on a
stump or other stable surface. Release the front handle
and let the saw fall by its own weight, rotating around the
rear handle towards the stump.
When the bar hits the stump the brake should be
applied.
Note! All service and repair work on the machine
demands special training. This is especially true of the
machine’s safety equipment. If your machine fails any of
the checks described below we recommend that you
take it to your service workshop.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 455 Rancher at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 455 Rancher in the language / languages: English as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 455 Rancher

Husqvarna 455 Rancher User Manual - English - 40 pages

Husqvarna 455 Rancher User Manual - German - 84 pages

Husqvarna 455 Rancher User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info