40844
30
Zoom out
Zoom in
Previous page
1/40
Next page
30 – English
MAINTENANCE
High speed jet H
At the factory the engine is adjusted at sea level. When
working at a high altitude or in different weather
conditions, temperatures and atmospheric humidity, it
may be necessary to make minor adjustments to the high
speed jet.
CAUTION! If the high speed jet is screwed in too far, it
may damage the piston/cylinder.
When test run at the factory, the high speed jet is set so that
the engine satisfies the applicable legal requirements at the
same time as achieving maximum performance. The
carburettor’s high speed jet is then locked using a limiter cap
in the fully screwed out position. The limiter cap limits the
potential to adjust the high speed jet to at most half a turn.
To adjust the carburettor correctly you should contact a
mechanic with access to a rev counter.
CAUTION! As the spark is cut off, the rev counter does not
show speeds higher than 13600 rpm.
Correctly adjusted carburettor
When the carburettor is correctly adjusted the machine
accelerates without hesitation and 4-cycles a little at full
throttle. It is also important that the chain does not rotate at
idle. If the L-jet is set too lean it may cause starting difficulties
and poor acceleration. If the H-jet is set too lean the machine
will have less power, poor acceleration and could suffer
damage to the engine.
Checking, maintaining and servicing
chain saw safety equipment
Chain brake and front hand guard
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain brake
and clutch drum. Dirt and wear can impair operation of the
brake.
Regularly check that the brake band is at least 0.6 mm thick
at its thinnest point.
Checking the front hand guard
Make sure the front hand guard is not damaged and that there
are no visible defects such as cracks.
Move the front hand guard forwards and back to make sure it
moves freely and that it is securely anchored to the clutch
cover.
Checking the inertia brake release
Place the chain saw, with the engine switched off, on a stump
or other stable surface. Release the front handle and let the
saw fall by its own weight, rotating around the rear handle
towards the stump.
When the bar hits the stump the brake should be applied.
Checking the brake trigger
Place the chain saw on firm ground and start it. Make sure the
chain does not touch the ground or any other object. See the
instructions under the heading Start and stop.
Note! All service and repair work on the machine demands
special training. This is especially true of the machine’s
safety equipment. If your machine fails any of the checks
described below we recommend that you take it to your
service workshop.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 455 Rancher at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 455 Rancher in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 455 Rancher

Husqvarna 455 Rancher User Manual - English - 44 pages

Husqvarna 455 Rancher User Manual - German - 84 pages

Husqvarna 455 Rancher User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info