40844
14
Zoom out
Zoom in
Previous page
1/40
Next page
14 – English
GENERAL SAFETY PRECAUTIONS
Checking chain lubrication
Check the chain lubrication each time you refuel. See
instructions under the heading Lubricating the bar tip
sprocket.
Aim the tip of the bar at a light coloured surface about 20
cm (8 inches) away. After 1 minute running at 3/4 throttle
you should see a distinct line of oil on the light surface.
If the chain lubrication is not working:
Check that the oil channel in the bar is not obstructed.
Clean if necessary.
Check that the groove in the edge of the bar is clean.
Clean if necessary.
Check that the bar tip sprocket turns freely and that the
lubricating hole in the tip sprocket is not blocked. Clean
and lubricate if necessary.
If the chain lubrication system is still not working after carrying
out the above checks and associated measures you should
contact your service agent.
Chain drive sprocket
The clutch drum is fitted with one of the following drive
sprockets:
A Spur sprocket (the chain sprocket is welded on the drum)
B Rim sprocket (replaceable)
Regularly check the degree of wear on the drive sprocket.
Replace if wear is excessive. Replace the drive sprocket
whenever you replace the chain.
Needle bearing lubrication
Both versions of sprockets have a needle bearing on the drive
shaft, which has to be greased regularly (once a week).
CAUTION! Use a high-quality bearing grease or engine oil.
See instructions under the heading Maintenance, Needle
bearing lubrication.
Checking wear on cutting equipment
Check the chain daily for:
Visible cracks in rivets and links.
Whether the chain is stiff.
Whether rivets and links are badly worn.
Replace the saw chain if it exhibits any of the points above.
We recommend you compare the existing chain with a new
chain to decide how badly the existing chain is worn.
When the length of the cutting teeth has worn down to only 4
mm the chain must be replaced.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Husqvarna 455 Rancher at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Husqvarna 455 Rancher in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Husqvarna 455 Rancher

Husqvarna 455 Rancher User Manual - English - 44 pages

Husqvarna 455 Rancher User Manual - German - 84 pages

Husqvarna 455 Rancher User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info